Interested to Buy Any Domain ? << Click Here >> for more details...
Explain the working principle of Synchronous Generator and
Assynchronous generator?
- 11 Answers
- 54911 Views
- TATA, I also Faced
- E-Mail Answers
Answer Posted / prasanth kumar
The word synchronous suggests that the rotor shaft runs at
synchronous speed,Ns=120f/p.when dc supply is provided to
the rotor shaft,it starts rotating in synchronism thus
developing 3phase alternating voltage on stator winding
which s then taken out...
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
what is the generator rating for 40 amp load of 3phase motor.?? 400v voltage of generator... plz tell me with formula its urgent...plzzz... and also tell me that this 40 amp at all phases mean 40 amp on red,40 amp on yellow,40 amp on blue...... or the total sum of that 3phase is 40 amp....
In Generator How suction compression power and exhaust works ?
Draw transformer phasor diagram.(full load,no load)
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
How to design the NGR Resistance
Diagram on interconnectivity of 11kv transformer with RMU (i.e, one incoming and two outgoing or two incoming and one outgoing)
How to calulate Locked rotor amper(LRA) for compressor type motors?
please write motor, transformer, Generator setting, fault level calculation of Tr.etc
I NEED RRB APTITUDE QUESTIONS AND MODEL PAPER,PLEASE SEND MY E-MAIL joo28_eee@yahoo.co.in
How can I calculate per unit (KWH) fuel (Gas/ Diesel both) consumption 1MW unit?
After completing iti in electrician, how can i get certificate of electrical supervisor? What ia requirements. For it?
In Air circuit breaker LSIG protection unit is used. Without fault in cables (2 runs 3Cx150Sq.mm Copper, 1Kv grade, XPLE armored cable IR value is more than 550Mohm @ 500V Megger) and load section Long time Overcurrent protection is triggers and trips the unit. We changed LSIG protection with new factory tested unit. Even then fault is persisting. Please suggest the possible causes
Why 11kv to be generated in generation station
What is meant by stator? What is meant by rotor?
From what on-site components does the HT panel monitoring the bus-bars in a 11kV system take inputs?
