what is coordinate measuring machine, how it work,how
accuracy of machine is defined also give me question and
answer related to cmm
vindudh@yahoo.co.in
- 2 Answers
- 9897 Views
- I also Faced
- E-Mail Answers
Answer Posted / trilok mehra
Total Station is a m/c for measuring coordinate.
| Is This Answer Correct ? | 5 Yes | 2 No |
Post New Answer View All Answers
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
Will going from a 3 tap to a 6 tap increase water pressure?
CAN ANY ONE TELL ME WHEN WILL CONDUCT ASSISTANT MOTOR VEHICLE INSPECTOR /RTO APPLICATIONS WILL RELEASE
What is isotropic material ?
hello sir iam atul joshi from mechanical branch. i want to know about the syllabus of technical ques of jindal steel
difference between microcontroller and microprocessor
"In a four-stroke diesel engine, In what engine exhaust valve will open?"
Define earth lamp?
Hindustan petroleum placement papers.please send me.
Explain the differences between pneumatics and hydraulics?
How are the pneumatic system and the hydraulic system similar?
why we r recommended for pre-action sprinklers @ generator/tx/mv panel room. If any leakage there,that panel will damage. So what is the Logic for pre-action sprinklers there?
Why you consider yourself suitable for the post
What is critical pressure ?. What will happen if water is heated above critical pressure and temperature?. What importance it is having related to Boiler?. Upto what presrure natural circulation is possible in Boilers?.
What is difference between mill and mill-drill?
