Interested to Buy Any Domain ? << Click Here >> for more details...
Categories >> Engineering >> Mechanical
Engineering
Suggest New Category
Question Asked @ Answers Views select
what is advantage of hllow shaft over solid shaft aprt from
material saving? does hollow shaft absorb more vibration
than solid shaft? 0 5
wat is the meaning of cop of wet suction and dry
suction????? 1 171
What is the difference between an axle and a shaft? reply
soon frnds........ 4 260
16 inch = 1 ______________? 2 124
What are the steps taken in troubleshooting of a machine
e.g extruder ME 0 26
What is a seal? ME 3 133
what is the mean of b.tech? 3 167
what type of pump 2 63
what is differance between ball screw and lead screw ?
Amtek 1 86
What is the units of surface tension and also dimensional
formula? RRB 3 218
What is meant by cigarcone? RRB 3 120
I want to know flow rate,max pressure drop,heat load,design
pressure,test presurre,temp both inlet and outlet of
coldside and hot side of 1,2,3,5,5.5,7.5,10,12,15 tons
0 24
why steam power plant is more popular than gas turbine
plant? ME 3 304
what is EEE in thermodynamics????? ME 2 223
what is the practical use of ENTROPY? JSW 4 282
- 1 Answers
- 3980 Views
- I also Faced
- E-Mail Answers
Answer Posted / ambarish
1) Hollow shafts are more homogenous in nature(material
property) and thus have more strength.
2)COP is coefficient of performance, in terms of wet suction
it is the ratio of liquid present to that of wet steam(which
include dry as well as liquid droplets)and dry is the vice
versa.
3)A shaft is a cylindrical device which transfers torque
only, it is a sub part of a axle, which is generally dead.
4)Trouble shooting of machines, in sense of engine can be
done by changing the conditions like fuel/air ratio, etc,
other steps can also be taking to prevent touble shooting ,
done basically by a governer, that is giving the solution to
the persisting problem.
6) its force/length, n/m.
7) if , u smoke cigar then its simple, the heating effect on
the cigar on its tip can be seen. the effect is the
formation of a cone due to suction of the smoke.
8)......info not clear.
9) Its cheap that is why, and steam has a higher latent heat
capacity also.
10).....
11) To find the stability of a system. Practical use nay
thermodynamic system like engines, boilers....
4) Mean of B.tech, I am not a engineer yet.
5)A ball screw is a mechanical device for translating
rotational motion to linear motion with little friction.A
leadscrew (or lead screw), also known as a power screw or
translation screw, is a screw designed to translate radial
motion into linear motion.
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
How can check gear pitch?
What is the ratio of specific heat of air?
What is mechanism?
why study in Michigan tech univ
What is a pneumatic system?
What is the material used ball screw rod
Describe How much Record maintain store Keeper and Write use of the Records?
What are materials used for manufacturing of gears ?
Explain why you consider yourself suited for the Position:
How is ceramic defined ?
I HAVE SELECTED INTERVIEW FOR GOVT POLYTECHNIC LECTURERS.I DONT KNOW ANYTHING.PLZ HOW INTERVIEW WILL GO AND WHAT QUE'S SUPPOSE TO ASK ABOUT SUBJECT.PLEASE SEND QUE'S AND ANSWERSTO MAIL OR CALL THIS NO:9966924990.PLZ HELP ME.
how does a generator work?
sir i appeared to bosch written test recently and i cleared it successfully.can u suggest me how the interview will be done ?is it technical or HR or both?how shall i prepare for it?i am very eager to work with and in fact it is my dream job suggest me how to grab the job.if you know tell what type books are prefer for preparation of intrview?
Why can't we use antifrictional bearing in place of journal bearing in a 660mw plant
What happen when the expansion valve is excessively open?
