Answer Posted / subramanyam
Voltages used are 1.5kV DC and 25kV AC for mainline trains.
Calcutta had an overhead 3kV DC system until the '60s.
The 1.5kV DC overhead system (negative earth, positive
catenary) is used around Bombay (This includes Mumbai CST -
Kalyan, Kalyan - Pune, Kalyan - Igatpuri, Mumbai CST -
Belapur - Panvel, and Churchgate - Virar). There are plans
[2/04] to change this to 25kV AC by 2010. In preparation
for this, BHEL has been retrofitting some EMUs with AC
drives to allow them to operate with both DC and AC
traction as the system conversion proceeds. Conversion to
25kV AC has already been done on the Titwala-Kasara
section; next to be converted are Khapoli-Vangani, Vangani-
Thane, and Titwala-Thane. The Madras suburban routes
(Madras-Tambaram in the '60s, extended later to Villupuram)
used to be 1.5kV DC until about 1967, when it was converted
to 25kV AC (all overhead catenary supply). (This is where
the MG DC locos were used, e.g., the YCG-1 series.)
The 25kV AC system with overhead supply from a catenary is
used throughout the rest of the country. The WCAM series of
locomotives are designed to operate with both DC and AC
traction as they move towards or away from the Bombay DC
section. The new [2003] AC-DC EMU rakes used in Mumbai are
also designed to operate with both DC and AC traction as
the Bombay area switches over to the 25kV AC system. Read
more about Mumbai area electrification.
The Calcutta Metro uses 750V DC traction with a third-rail
mechanism for delivering the electricity to the EMUs.
The Calcutta trams use 550V DC with an overhead catenary
system with underground return conductors. The catenary is
at a negative potential.
The Delhi Metro uses 25kV AC overhead traction with a
catenary system on the ground-level and elevated routes,
and uses a rather unusual 'rigid catenary' or overhead
power rail in the underground tunnel sections (Line 2).
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
What the main causes of transient interruptions on Over-Head Distribution Lines?
please send the last 5 years {{{JUNIOR ENGINEER - ELECTICAL, ELECTRONICS RRB CHENNAI and secundrabad}}} TECHNICAL question papers TO MY EMAIL ID dinesh100701@gmail.com
why and how voltage sharing in transformer, during magnetic balance test ?
Draw the circuit of clapp oscillator?
can you send me the placement papers of electrical engg. from companis like NTPC,DRDO,IOCL,HPCL,BPCL etc.?If,plz send as soon as possible.Thanks.
I want single line diagram for AMF & DG syncronizing panel
sir am giving jspl exam on 19th oct . i belong to eee, so plz send previous question papers ..........to dis id abhilash203@gmail.com
1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.
plese send me the oces/dgfs sylabus and previous year question pattern of electrical engg.?
What was your role in the silicon evaluation/product ramp? What tools did you use?
hai friends i have BSNL JTO exam on next month so if any body have model question paper or give preparation tips to my mail id kumar4486@yahoo.co.in this will helpfull for my future .plz & thank u by kumar
i m in need of current rating chart of heavy duty pvc/xlpe, cu/al cables. can somebody provide me? if yes, plz send me at ashish_patel111@yahoo.com
Is there a standard depth of gravel fill in Substation Switchyard? Please give a design/drawing. Thank you.
please send me jindal previous aptitude and technical question and answer.my email id is deep_raj@live.com
could anybody able 2 send me jindal steels previous papers fr electrical steam....pls send 2 my id if possible....sirisha.shaik@gmail.com
