Interested to Buy Any Domain ? << Click Here >> for more details...
What is trim material . Why it is known as trim.
- 1 Answers
- 6614 Views
- L&T, LNG, I also Faced
- E-Mail Answers
Answer Posted / hassanelect
The internal elements of a valve are collectively referred
to as a valve's trim. The trim typically includes a disk,
seat, stem, and sleeves needed to guide the stem.
A valve's performance is determined by the disk and
seat interface and the relation of the disk position to the
seat. Because of the trim, basic motions and flow
control are possible. In rotational motion trim
designs, the disk slides closely past the seat to
produce a change in flow opening. In linear motion
trim designs, the disk lifts perpendicularly away from the
seat so that an annular orifice appears
Reference:
http://www.tpub.com/content/doe/h1018v2/css/h1018v2_23.htm
| Is This Answer Correct ? | 8 Yes | 1 No |
Post New Answer View All Answers
why orfice is not used for main steam flow calculation
Can any one send me IOCL instrumentation question papers.. i dont know the pattern of the questions and what to prepare can any one help me on this .. my email id is anwarnishil@gmail.com
What pressure results for a flow transmitter of range 0- 180t/h in the dcs and 0-301mbar in the field using square root extraction. Kindly also suggest formulae for the percentages 0,25,50,75,100?
how to measure oxygen which methods are using?
what is IEC code in cables & how to selecting cables?
use of split range ? where it is used ? in which control loop it is used ?
can we replace a slot sensor (inductive type) with limit switch (potenial free contact / no-nc type).
how can we tune a PID. If it is by zeiger nichols method..please explain briefly with help of an example.
what is output of FOUNDATION FIELD BUS transmitter
What is difference between “Fault Tolerant” & “Fault avoidance” PLC? Application where these system s are used?
full process of gas turbin?
why direct mounted pressure transmitters is always installed with DBB ( double bleed block) valve in process line or top of the tanks ?
TEMPERATURE VARIATION FOR FREQUENTLY.
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
we have a s-5 simense plc having op7 .recently on op7 showing error 1.plc not present 2. DB error frequently. can u have any solution . please send me.
