why don't we use 2 nd angle and 4 th angle
projections ??????(since there is also NOT overlapping of
VIEWS in 2 nd angle and 4 th angle projections)
- 2 Answers
- 4952 Views
- I also Faced
- E-Mail Answers
Answer Posted / govind
we need only two quads to properly define a part. For
theoretical part 1st angle is gud as newbies grasp this
concept easily but manufacturing point of view 3rd is
preffered as machinist graps 3rd angle view more easily.
the reason for selecting 1st and 3rd and not 1st and 2nd or
1st and 4rth is that using diagonaly opposite quads we can
get 100% sketchable view of a part fronm every angle be it
top,front RHSV,LHSV,bottom and top. Now dont get yourself
entangled into this already messy affair and accept it as
it is because it does the job well.
| Is This Answer Correct ? | 6 Yes | 2 No |
Post New Answer View All Answers
What is the different types of surge tanks ?
What are the different types of fits? Explain
What do you understand by engineering drawing?
What are the benefits of cycloidal gears?
Why do you want do MS in Mechanical Engineering in US
sir i need section engineer test papers
What kinds of pipes are used for steam lines?
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
Hello Friends I had my ONGC test today,but it was very bad.But I would give certain suggestions so that u may not face he problem which i had. Be thorough with Electrical Technology.Generators.motors stators etc.There are 5 questions on that. There were also good no.of questions from Hydraulic machine and Production technology. Then 3 from Strength of materials.And remember the dimensional quantities.
Name Of Parts And Each Purpose
I am a mechanical student.And have cleared the written for NTPC. Please suggest what and how to prepare for the interview.i have got only 2-3 weeks in hand.
While normal carburising and nitriding surface treatments increase fatigue strength, excessive treatment may decrease the fatigue strength. Why ?
will I find the mechanical engineering interview question for asian paints?
Whether entropy is intensive property or extensive property ?
i am preparing for motor vehicle assistant inespector please send me old questions papers.
