Interested to Buy Any Domain ? << Click Here >> for more details...
How to find Cable size?
Caterpillar generator produce (Two generators) 127*2=254 amp
at 11 kv .
What would be the cable size (XLPE) to supply 256 amp at 11
kv? Air or surrounding Temperature is 32 degree C. Cable
will go under ground at 2.5 feet depth. Group Rating Factors
is 3 cables. Clearance between cables is 7 cm. Soil
Temperature (Ambient) 28o C Soil Thermal Resistivity is 1.2
K.m/W
I would like to use 3 separate single core instead of using
3 core cable.
Some says I should use three separate single core 120RM cables.
Some says 70RM .some says 95.
I m totally confused.
Is there ant specific rule to determine cable size?
What would be the LT cable size to flow 500 Amp current?
Ifte
My e mail address is ifte13@yahoo.com
Anyone please send me the answer to my e mail address,
i will be very glad.
- 1 Answers
- 8510 Views
- I also Faced
- E-Mail Answers
Answer Posted / muhammad qasim
Dear, All those specification you described in your question
are cared while manufacturer design their product. Designing
contains many complex parameters to be cared while deciding
about the metallurgy, insulation. All good manufacturer care
worst operating conditions when they design their products.
When we go for their usage in industrial sector, main things
we need to assure are that:
1- Current Raging
2- Voltage Drop should not exceed the permissible level
3- Cable should have withstanding capability for transient
short circuit and thermal capability.
Normally, copper have current density of 1000 A/Sq inch
which becomes 1.8 A/Sq mm. and all cable and bus bars should
be designed 150% of operating rating for safety purpose.
Secondly, Conductor area is not affected with voltage level,
50 A at HT or LT shall require same conductor area but
insulation level shall be affected. For HT you need XLP and
for LT you need PVC-PVC cables.
Further if you get better answer please copy the same to
muazmi02@yahoo.com
Regards
| Is This Answer Correct ? | 4 Yes | 0 No |
Post New Answer View All Answers
Scott connection is used for A 3-phase to 2-phase conversion B to achieve higher effciency C to save copper D to reduce harmonics
i am going to correct power factor of 1600kw induction motor,when i calculate capacitance of capacitor it is three time more in star connection than delta. if motor is star connected which connection i shall adopt for capacitors and reason for adopt this connection
How to design the no. of ceiling fans required in 5mtr X 10 mtr X 3 Mtr hight room?
how to differentiate a mpcb,mcb with a contactor? Explain their working operation
What is minimum permicible value of leackage current for LT Panle when applying voltage up to 3 KV for 5 Minuits?
What are the types of piano switches?
WHY THREE PHESE SYSTEM VOLTAGE APPLIED IN 440 VOLT
lorteny method
for what voltage will reactive power be largest in 380 kv line : a) 375kv b)380kv c)385kv
how to protect motor in dol starter having capacity of 30 hp.40 hp?
Does magnetomonopoles exists? one maxwell equation strongly suggests no, but how about their existance in plasma?
What is the unit of magnetic flux density?
3 shows a 415 V, 3-phase generator supplying a 3-phase 415/110 V transformer. Draw the individual and combined impedance diagrams to a base of 10 kVA. Determine the system fault kVA and the fault currents at the 415 V and 110 V busbars for short circuit faults on the transformer input or output terminals. Work in p.u. values of impedances.
and gate circuit diagram,amplifier circuit diagram
What will be the fault current of any system when its generation is 10% of BASE generation( FUll Load )?Will is 10% or the same as full base calculation?
