Interested to Buy Any Domain ? << Click Here >> for more details...
generally on the roadside v hav 11kv line which is being
step down to 440v line to line....so any1 can tell me which
type of transformer they r using whether it is star to
delta,delta to star etc...???
- 9 Answers
- 15668 Views
- Core Solutions, I also Faced
- E-Mail Answers
Answer Posted / bhanu
The transformer is Delta - Star connected Transformer i.e.,
11kv is given to Delta connected side and 440v is given to
Star connected side of the transformer.
Delta side dont have neutral, while transmission neutral is
not needed.if neutral is used totally 4 wires have to be
used otherwise 3 wires are enough. 440v side we give to
homes, there a neutral is need so connected in star.
in Delta side line voltage = phase voltage. so 11kv voltage
is same.
homes need the voltage of 230v, in star the line voltage is
not equal to phase voltage. line voltage is 440v and phase
voltage is 230v.
so the transformer needed is Delta-Star
| Is This Answer Correct ? | 9 Yes | 1 No |
Post New Answer View All Answers
What is the exact minimum vale of voltage between an earth and netural which can damage or can do malfunction of the electronic equipments ? If this is mentioned in any book, pl.give reference.
What are the advantages of a three-phase system over a single-phase system?
1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.
Air circuit breaker safety
In case of HV test on medium voltage cables, BS is asking for 4 U0 where as IEC is asking for 3.5 U0. Can any one advise me how this 3.5 times or 4 times U0 is derived?
In a synchronous motor. if start is running at high speed. What will be the starting torque : Higher Lower Zero
please send me previous year questions of jspl through which i could prepare myself for the test.
what's the requirement of Dy11d0 connection of 3 phase transformer?what's use of it?
Is there any guideline say about display of earthing value near to earth pit
How can i calculate the Breaking capacity of molded case circuit breaker, is the breaking capacity of CB for Diesel generator shall be less than grid supply's breaker ?
hi, in the event earth grounding is not available in a project, is there any other way to make the elcb work? fyi, i have an instant water heater (6.5kw) installed, however if there is grounding in the heating element inside the heater assembly, i will get grounded. thank you in advance to those who will answer my question.
What is the basis for framing the rules of block diagram reduction technique?
What is the function of auadag in a cro?
WHAT IS IM (INDEX OF MOUNTING )IN MOTORS
1. What is the exact formula for one weber? for example,(one ampere = one coulomb electron of electrons crossing a point of conductor at one second. i.e, 1A=1Q/1sec)
