Interested to Buy Any Domain ? << Click Here >> for more details...
What are the Steps for Testing of 20MVA (make:-CGL)
Transformer? How many Test we have to do?
- 2 Answers
- 9530 Views
- BSL, I also Faced
- E-Mail Answers
Answer Posted / rajendran
The depth of the testing procedures adopted depending upon
the application where it is installed and various service
conditons of the transformer..... however following are
basic tests which can not avoided...
1) IR
2) Ratio test
3) Vector group
4) Magnetic balance
5) Visual inspection
6) Tap changer tests
7) Special tests to see the condition of the dielectric
strength
8) DSA - dissolved gas analysis "(Predicative type)
thanks
| Is This Answer Correct ? | 7 Yes | 7 No |
Post New Answer View All Answers
1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.
how is find out kwh step by step
What are the essential characteristics of signal flow graphs?
What kind of Neutral CT can be placed in 11/0.433KV transformer to be used and what are its specification?
a)In a 3-phase 4-wire circuit, a circuit breaker is selected to protect the circuit whose highest fault level is 6.6 MVA. Determine the required minimum breaking capacity in kA. (Note: Covert 3-phase power in terms of kA to find answer.) b)Using the below, determine the required minimum making capacity in kA as a “peak value”. Rate breaking capacity (Icn) ka: Icn<= 1.5 Factor = 1.41 1.5
what is the working principle of a DG Set, Alternator, & exiter
on a three-winding transformer relationship delta-delta-star, on third winding why the relationship is a star? what are the advantages and disadvantages? Thank you and please help
I am going to appear for the RRB Chennai junior Engineer online exam. Please send me the previous exams question papers (also solved) to my mail id: rrkhandhar@yahoo.com
For the requirement of a furnace of temperature range up to 1200 oC using silicon carbide rods, What is the required rate of transformer needed (please do it with all details)?
The D.C. spark test is applicable to single conductor cable & assemblies of insulated single conductor cables without insulation shield,metallic sheath or metalic armor?
what is the difference between gas group b and gas group c electrical equipment construction wise?
The SFC of an engine is 0.25 kg/kW hr. when the fuel used has a calorific value of 36000 kJ/kg. the thermal efficiency of the engine is
what is differentila pilot supervision in the incomer control panel in the power station?
What is an 86-P or an 86-A trip
What is the limitation of kirchoffs law?
