Interested to Buy Any Domain ? << Click Here >> for more details...
How a synchronous generator practically work? what is the
function of avr(automatic voltage regulator)in synchronous
generator?how the connection of avr to the generator made
practically?please give me the answer.
- 6 Answers
- 32455 Views
- Accenture, Heineken, I also Faced
- E-Mail Answers
Answer Posted / thillai natarajan
practically,Synchronous Generator operated by DC self
excitation.
Totally , It consist of Synchronous generator, PMT
generator,rotating rectifier,AVR,External rectifier and
Battery arrangements.
The rotor(excitation winding) of the synchronous generator
is connected along with rotating rectifier and Permanent
magnetic generator in the same Driving shaft ,
The permanent magenatic generator generates AC Supply in
this rotor, This 3Phase AC Supply is converted into DC
supply by Rotating rectifier,
then,this DC source feed to Rotor winding (Excitation)of
Synchronous generator.
then,Synchronous generator generate the Final 3 Phase AC
supply from stator winding.
The Automatic voltage regulator(AVR) is get two DC Supply
source ,one is from DC Battery and another from External
Rectifier(AC supply from Synchronous generator is
converted into DC output),The function of AVR is maintain
Constant DC source and feed to stator of the PMT generator.
| Is This Answer Correct ? | 48 Yes | 22 No |
Post New Answer View All Answers
what rectifiers is and what are the types of rectifiers?
How to check the thermocouple is correctly connected to cable for K type? (i,e positive pole is connected to non magnetic conductor and negative pole is connected to magnetic conductor)
What is inverse definite minimum time lag relay? Where is it use?
For R-L or R-C ckt,time constant formula is L/R and RC respectively and its unit is in sec.Pls tell me the derivation
The specific heats of the gas at constant pressure and constant volume are respectively 1.0 kJ/kg K and 0.72 kJ/kg K; the value of R for the gas is
Good morning: I'm looking for some informations about the OLTC or the LTC: I wont to know what the function of the tie-resistor in during the operation of reversing/coarse operation Cordially
HOW TO CALCULATE THE HEAT AND LOAD OF LT-SUBSTATION WHICH CONTAINS 2*1MVA TRANSFORMERS,LT SWITCH BOARD,MLDB,ACB,BUSBAR,ETC...?
I need a formula to calculate the size of cable as per load but in the terms of length. Please Reply me as i search lot of sites but i did not get the answer.
What is cable tray, its type, and its support?
Can 4pole (3 phase+neautral )RCCB proper functioning in only 3 phase load (no neautral, no Earth) ?
Can Anyone Answer anyone of these ? Q1) why direct SOLUTION of Load Flow Studies in Not Possile ? Q2)Why majority of Buses in power system are load buses Q3)Why one of the buses in Power system is taken as reference bus (slack or swing) Bus ? Q4)Bus Admittance Matrix is a sparce (means it contains some zero elements ) matrix , give reason
Why is back emf used for a DC motor? Highlight its significance.
why we use the 100% and 95% stator earth fault protection for the synchronus generator ?
1. What is differential relay? How it operates? 2.How to calculate the Short Circuit Impedance in Transformer? 3.What is the alternate solution for testing of polarity by using polarity tester while its milli ammeter does not works? 4. While testing the 33KV Busbar by using Hipot kit, what should be the test voltage we have to apply? 5. What is the procedure/activities to be taken to inject the current more than 2000A by using 2000A Loading Transformer? 6. Explain how you can give the overload setting to any Motor Protection Relay for a HT motors with formula and example? 7. Why restricted earth fault protection is needed? Why can’t differential Protection is sufficient? 8. What should be the minimum and maximum ohmic value for earthing? 9. Why DC Currents are not used in transformer? 10. What is the Frequency while we step up the voltage from 220V to 11KV? Is it possible? Explain it?
If we use 250A MCCB as a incomer in Control panel for a fault level of 50kA for one second ,assuming temperature rise from 85 Deg. to 100 Deg , Then what will be the Aluminium Bus-bar size for 250A MCCB? Explain in detail.
