Interested to Buy Any Domain ? << Click Here >> for more details...
hi i am chemical engg. 4 year student i am not placed till
year what will i do for my batter futere
- 3 Answers
- 6149 Views
- I also Faced
- E-Mail Answers
Answer Posted / sada
hi.....i am also a chemical eng....working in reliance
petrochemical groups.... upto me ....if u want a job go
through o.p guptha and general aptitude books and attend
all the entrance exams.....u will....gwt a job.......
| Is This Answer Correct ? | 4 Yes | 2 No |
Post New Answer View All Answers
What are the factors involved in considering the choice of dry screw compressor?
What are the specialized grinding methods?
Define pcbs?
Explain the steps required to design a vapor-liquid separator or flash drum?
What information is needed to specify a mixer?
Explain the reasons of removal of particles from effluent gas?
X is strong but has a very low density (1% of traditional earth materials.) and hence light weight. It is a recyclable material. The compression behaviour of X is strain rate dependent. Higher strain rates result in higher initial modulus and higher compression strength. It can also withstand unlimited number of cycling loading provided the repetitive loads are kept below 80% of the compressive strength. The internal structure of the material includes air-traps which make it poor heat conductor. X is non- biodegradable and chemically inert in both soil and water. Most acids and their water solutions do not attack it; however strong oxidizing acids do. Solvents which attack X include esters, ketones, ethers, aromatic and aliphatic hydrocarbons and their emulsions, among others. It does not support bacterial/fungal growth as well .It also has significant acoustic properties and effectively reduces the transmission of airborne sound. X is combustible and should not be exposed to open flame or other ignition sources. Combustion products are carbon monoxide, carbon dioxide, water and soot. Long-term exposure to sunlight causes yellowing and a slight embrittlement of the surface due to ultraviolet light. X is able to withstand the rigours of temperature cycling, assuring long-term performance.
I am a Diploma Chemical Engineer by Nirma Uni; and BEng (Hons) Energy & Environmental Engineer by Napier Uni; Edinburg, UK. HPCL chemical engineering test will held on 14th July,09. So, Please send me some previous chemical engineering papers Objective types Or material to give the test.
How does a tank-blanketing valve operate?
What is an isochoric process?
Explain what type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?
How much maximum power can be generated by 320v, 10kg-cm synchronous motor if shaft is rotated mechanically at 50 to 60 rpm?
What are the factors involved in designing kettle type reboiler?
What is condensate lift?
MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)
