Where do we consider the pressure in mbar & where do we consider the pressure in bar & why is it so ?

BOC, Jindal Steel and Power,

How does pressure transmitter electronics sensor be used to transmit level measurement parameter?

What is difference between high pressure gradient and low pressure gradient ?

Aurobindo, Lee Pharma,

In which state sulphur exists at 40 degrees temperature and 40 atmospheric pressure in natural gas having sulphur composition 0.1 ppm?

Nagarjuna Fertilizers, NFCL,

Question 64 – According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

which material is suitable for punching press to avoid scratches amd waear of metal hittimg the blades?

Delta Thermoformers, Tata Steel Limited,

In compression level all requests are becoming zero which data is compressing tell me detail

Rockwell, TCS,

how to calibrate pressure gauge(we can not able to fixed by pointer screw adjustment and pointer re fixing method)

Nestle, Reliance,

On Which Pressure PRV is operated.

AEPL,

How Much static pressure as per NFPA standard is required in the hydrant line?

whats the Formula to calculate temperature of steam at given pressure

I am applied 100 % pressure on to the air to open control valve,but the valve is not fully closed..and 10-15% is open the valve. how to calibrate the control valve?

OPaL,

Question 78 - Fact 1 : Dry air contains 20.95 % oxygen, 78.09 % nitrogen, 0.93 % argon, 0.039% carbon dioxide, and small amounts of other gases by volume. Fact 2 : Volume occupied is directly proportional to the number of moles for ideal gases at constant temperature and pressure. Fact 3 : 12.5 moles of pure oxygen is required to completely burn 1 mole of pure octane. Fact 4 : Air–fuel ratio (AFR) is the mass ratio of dry air to fuel present in a combustion process such as in an internal combustion engine or industrial furnace. Fact 5 : Molecular weight of oxygen gas is 31.998 g / mole and molecular weight of nitrogen gas is 28.014 g / mole. (a) Find the molar ratio of nitrogen and oxygen, or (moles of nitrogen) / (moles of oxygen) in dry air, by assuming ideal features of nitrogen and oxygen gases. (b) How many moles of nitrogen are available if dry air is used to completely burn the 1 mole pure octane? (c) Find the mass of fuel of 1 mole of octane with molecular weight of 114.232 g / mole. (d) Find the mass of dry air with 12.5 moles of pure oxygen by assuming only oxygen and nitrogen gases exist in the air. (e) Find the air-fuel ratio (AFR) when octane is used as fuel. (f) Find the fuel-air ratio (FAR) when octane is used as fuel.

CHEMICAL MATERIAL BALANCE - EXAMPLE 2.4 : A mixture consists of benzene (B), toluene (T) and xylene (X). At a temperature of 353 K, the data of vapor pressures : B : 754.12, T : 289.71, X : 91.19. Unit is mm Hg. The pressure P is 0.5 atm. The value of k for each substance is k = (vapor pressure) / P. (a) Calculate k for B, T and X. Let L / V = 0.65. (b) By using the equation V = F / [ (L / V) + 1 ], find the value of V when F = 100, then what is the value of L?

CHEMICAL MATERIAL BALANCE - EXAMPLE 2.5 : In a non-dilute absorber, the inlet gas stream consists of 8 mol % carbon dioxide in nitrogen. By contact with room temperature water at atmospheric pressure, 65 % of the carbon dioxide from a gas stream has been removed. (a) Find the mole ratio of carbon dioxide and nitrogen gases at inlet and outlet gas streams. (b) The Henry's Law provides y = 1640 x for carbon dioxide in water. Find the mole ratio when x = 0.0000427. Mole ratio is y / (1 - y) for y.