The simple way of finding the leakage quantity and % in compressed air distribution system
- 1 Answers
- 1745 Views
- I also Faced
- E-Mail Answers
Answer Posted / Arvind Kumar Sinha
To find the leakage quantity and percentage in a compressed air distribution system, follow these steps:
1. Measure the total flow rate (Q) of the compressed air system at a given time.
2. Measure the pressure drop (ΔP) across the system during operation.
3. Identify the flow rate of compressed air being delivered to the tools and equipment (Q_used).
4. Calculate the total leakage flow rate (Q_leak) by subtracting Q_used from Q:n```math
Q_{leak} = Q - Q_{used}
```
5. To find the percentage of leakage, divide Q_leak by Q and multiply by 100%.n```math
Leakage \% = (Q_{leak} / Q) * 100%
```
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
How much minimum insulation required between 11kv/3.3kv transformer windings?
XYZ
previous year paper of ntpc bhel for degree in electrical enng
where are the circulat the diesel in DG parts name with pictue
kindly send me 11KV MV motor differential protection procedure by primary injection method.
please send the last 5 years {{{JUNIOR ENGINEER - ELECTICAL, ELECTRONICS RRB CHENNAI and secundrabad}}} TECHNICAL question papers TO MY EMAIL ID dinesh100701@gmail.com
What is the height of DA, DAL, DB, DC & DDE tower?
1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.
Define the overload capacity of the motor?
In PFI plant one stage capacitor connection is directly connected(with out megnetic contact controll). but why?
I want single line diagram for AMF & DG syncronizing panel
how you will decide the distance between the power transformer and its fencing
IF ANYONE HAVE ANY QUESTION ASK ME AT MY MAIL anmol.bhardwaj5@gmail.com
hi this is hema, r there any books in particular for the preparation of the APPSC-A.E.E(electrical), if so please mail me the names ... thank u .
A 15 kw squirrel cage motor having a maximum efficiency of 90% on a continuous full load has temperature rise of 42 degrees celcius after 30 min and 52 degrees celcius after 1 hr under the above operation conditions. a) calculate its final steady state temperature rise on continuous load and the heating time constatnt. b) if the motor is operated on a short load for 9 min estimate its temperature rise. c) calculate the maximum overload that can be applied on a short, 9 min rating so that the temperature rise is the same as the final steady state temperature rise on continuous load.
