:: Home Page
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   Errors
   Testimonials Refer this Site  Refer This Site to Your Friends  Site Map  Contact Us      
Categories >> Engineering >> Electrical Engineering


Question Why a starter is used for a motor?
 Question Asked In Companies :: L&T, Nilachal Polytechnic,     < I also faced this Question! >
 Question Submitted By :: ravi
  Answer Posted By  
Starter is used for a motor to limit the high starting
current. During starting of a ac motor high current of upto
4-5 times the full load current.and then start/stop switch
on the motor

Is This Answer Correct ?    16 Yes 13 No

View All Answers
Please Help Members By Posting Answers For Below Questions
 Question Views   Select
How the setting of the vector surge relay shall be calculated when the relay is to be used for Grid islanding application? 295
why the earth is taken minimum in supplying? wather it the proportional factor to getting work any equipment or a power plant? 265
What is ignition module of a CAT Gas Genset G-3508 Engine, Alternator SR4B Series. HOw its checked for correct functioning.Is it repiarable or replacable? 587
Dear Mr B C pal...Can you plz. put some light on principle of operation of Z-Ct in conjunction to its use with 1Cx1000Sqmm HT Cables & Directional Ground Fault / Over Voltage Relays...Regd..Parag v K 9899115632 1046
What is the difference between PLC & DCS? 564
star delta starter contorl circuit... drawing.. 428
how we can decide that what value of ht line will come to any commercial building? (ans except According to the building load) 46
What are all the problems occured while ac generator running in leading power factor at full load condition? 365
A T-T transformer can not be parallel with transformer A V-V B star-delta C star-star D delta-delta 692
hi friend i am going too attend for hpcl in this month please help me by sending written test question papers i am in the stream of E.E.E 416
how harmonics generated in induction furnance? how minimise it? 462
For the requirement of a furnace of temperature range up to 1200 oC using silicon carbide rods, What is the required rate of transformer needed (please do it with all details)? 331
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1.  H1-H2 = H2-H3 H3-H1 2.  H2-H3 = H3-H1 H1-H2 3.  H3-H1 = H1-H2 H2-H3 For the LV side also: 4.  X1-X0 = X2-X0 X3-X0 5.  X2-X0 = X3-X0 X1-X0 6.  X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0  H2-H0  H3-H0    X0-X1  X0-X2  X0-X3 128.0  119.9  7.2      29.2   13.3   15.8 70.7   128.4  59.2     23.4   22.0   3.6 7.2    120.1  128.1    13.4   29.3   15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone? 85
If you don’t have coal, salt and copper, then how would you earth your connection temporarily at a camp site.? 406
E-Mail New Answers        Answer Selected Questions