| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which two statements accurately define IP addressing rules?
(Choose two)
A. IP multicast addresses start with 240
B. A host Carbon of all 1 a indicates a network broadcast
C. The value of zero (0) in the host Carbon means all hosts
on the network
D. IP addresses are four octets long and contain a network
Carbon and a host Carbon | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| The command "show IP protocol" displays which information?
A. routing timers
B. network information
C. contents of the IP routing table
D. information about all known network and subnetworks | | 2 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 2 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 1 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| Which IP host address range is allowable given an IP address
of 172.37.2.56 and 12 bits of subnetting
A. 172.37.2.48 to 172.37.2.63
B. 172.37.2.48 to 172.37.2.62
C. 172.37.2.49 to 172.37.2.62
D. 172.37.2.49 to 172.37.2.63
E. 172.37.2.55 to 172.37.2.126 | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| How signalling can be explained in D channel of ISDN? | Tulip | 1 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 1 |
| Which three protocols are corerectly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not at
the same time | | 1 |
| What is the default IPX Ethernet encapsulation?
A.) SNAP
B.) Arpa
C.) 802.2
D.) Novell-Ether
E.) SAP | | 2 |
| Hi,
I am littl bit confused about ip Addressing scheme? can
someone tell me how can we assign ip addresses to pc | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
