| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the extended IPX access list range?
A.) 901-1000
B.) 100-199
C.) 900-999
D.) 1000-1000 | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 2 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| MIDI and MPEG are examples of what layer of the OSI seven layer
model?
A.) Session
B.) Network
C.) Datalink
D.) Transport
E.) Application
F.) Presentation | | 4 |
| Which device listed below provides clocking for the line?
A.) DCE
B.) CPE
C.) CO
D.) DTE
E.) Demarc | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Repeaters work at which layer of the OSI model?
A.) Network
B.) Session
C.) Transport
D.) Physical | | 3 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which of the following provide connection-oriented transport to
upper layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| When using access lists, it is important where those access
lists
are placed. Which statement best describes access list
placement?
A. Put standard access lists as near the destination as
possible. Put
extended access lists as close to the source as possible.
B. Put extended access lists as near the destination as
possible. Put
standard access lists as close to the source as possible.
C. It isn't import where access lists are placed since the
router will
read and cache the whole list.
D. Put access lists as close to corporate headquarters as
possible. | | 1 |
| 255.255.255.128/what is the n/w id ,broadcast id and the
number of valid host(according to disco rules) | Reliance | 2 |
| What is the first step in data encapsulation?
A.) User information is converted into data.
B.) Frames are put into bits.
C.) Data is converted into segments.
D.) Segments are converted into datagrams and packets.
E.) Packets are put into logical frame. | | 1 |
| Identify the X.25 addressing standard?
A.) X.121
B.) X.25a
C.) ITU-1
D.) Q933a | | 1 |
| WHAT IS SERIAL TRANSMISSIONS,PARALLELL TRANSMISSION | ASD-Lab | 2 |
| PICT & JPEG are examples of what layer in the OSI seven
layer model?
A.) Transport
B.) Presentation
C.) Application
D.) Datalink
E.) Network
F.) Session | | 1 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| Identify the 2 commands to copy a configuration from a TFTP
server
to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
