| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| intial information of packey occur on which layer
application
sessions
physical
mine answer physical | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. Which two factors must you consider when you define
the subnet
mask for the network?
A.) The location of DHCP servers
B.) The volume of traffic on each subnet
C.) The number of subnets on the network
D.) The location of the default gateway
E.) The number of host IDs on each subnet | | 1 |
| What is the distance limitation for 100BaseT?
A. 305.955 ft
B. 7283.46 inches
C. 184 Meters
D. 185 Kilometers | | 3 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| Identify the true statement regarding subnetting?
A.) Allows for more host address
B.) Borrow bits from the network portion of the address
C.) Allows for unlimited number of networks
D.) Borrow bits from the host portion of the address | | 1 |
| What does the ping response & mean?
* A: unreachable
* B: congestion
* C: user interrupt
* D: unknown packet type
* E: lifetime exceeded
| | 2 |
| Port selection is done at which layer of OSI reference
model????? | | 3 |
| How do you set the encapsulation type to PPP for an interface?
A.) encap ppp
B.) ppp encapsulation
C.) encapsulation ppp
D.) encapsulation ppp enable
E.) ppp enable encapsulation | | 2 |
| as we know that isdn bri port come with either a u
interface or some thing s/t interface what is the
diffrenmce between them | HCL | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Based upon the 1st octet rule identify the range for a Class A
address?
A.) 1 - 126
B.) 192 - 223
C.) 128 - 191
D.) 1 - 191 | | 1 |
| What is the purpose and default value of the CDP timer command?
A.) 90 seconds; interval before an entry expires
B.) 60 seconds; interval between updates
C.) 60 seconds; interval before an entry expires
D.) 90 seconds; interval between updates | | 1 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| What parameter is used with statically assigned routers to tell
packets
which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface | | 1 |
| Which of the following is a valid TCP/IP socket for an
Email connection?
101.34.2.125:25
00-00-03-1B-CA-6F:143
202.167.23.101:21
60.4:110
| | 1 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| How we ping ICMP a NIC with a correct IP address but with
wrong MAC address
Do all NIC's can run inpromiscuous mode | Cisco | 3 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| |
| For more CCNA Interview Questions Click Here |