| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| can we configure multiple as on single router using eigrp | IBM | 1 |
| What does the following series of commands accomplish?
router igrp 71
network 10.0.0.0
router igrp 109
network 172.68.7.0
A. It isolates networks 10.0.0.0 and 172.68.7.0.
B. It loads igrp for networks 109 and 71.
C. It disables RIP.
D. It disables all routing protocols. | | 1 |
| Identify 3 LAN technologies?
A.) FDDI
B.) HDLC
C.) HSSI
D.) X.25
E.) 802.3
F.) 802.5 | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| The benefits to segmenting with Bridges are which of the
following?
A.) Scalability
B.) Datagram filtering
C.) Manageability
D.) Reliability | | 1 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| With distance vector routing protocols, it is never useful
to send
the same routing update packet back out the same interface
that it was
learned. This concept is called what?
A.) Holddown timers
B.) Poison Reverse
C.) Count to infinity
D.) Split Horizon
E.) Link State | | 2 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| What is the difference between TCP and UDP?
A.) TCP is connection-oriented; UDP uses acknowledgements only
B.) TCP is connection-oriented; UDP is connectionless
C.) Both TCP and UDP are connection-oriented, but only TCP
uses windowing
D.) TCP and UDP both have sequencing, but UDP is connectionless | | 2 |
| You have typed "ping" 172.16.101.1 and get the following
display:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 172.16.101.1,
timeout is 2 seconds:
.!!!!
What does the "." signify?
A. That one message timed out.
B. That all messages were successful.
C. That one message was successful.
D. That one message completed in under the allotted
timeframe. | | 1 |
| What is difference between standard and extended access-list | HCL | 8 |
| hi friends i have some problem regarding technical round
ahr round plz tell me what should the right answer
technical questions
1 what is brouter
2 what is the menaing of 10 base2, 10 base 5 and 10baset
3 what is diffrence between bit rate and baud rate.
and this question was tooooooooooo much difficult to me
that
hr said to me that
rank me after the taking the all short of interview | | 5 |
| Which layer of the 7 layer model provides services to the
Application layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| what is meant by domain ?
what is mean by DNS? | | 14 |
| b Which protocol for PPP LCP (Link Control Protocol) performs a
challenge handshake?
A. CHAP
B. PAP
C. UDP
D. IPX | | 1 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| What is difference between Store-and-Forward, cut-through,
Fragment-Free Method? | Microsoft | 2 |
| What would be the proper wildcard mask to permit all odd
numbered hosts on the 10.48.0.0/12 network?
access-list 1 permit 10.48.0.0 0.15.255.255
access-list 1 permit 10.48.0.1 0.15.255.254
access-list 1 permit 10.48.0.0 0.15.255.1
access-list 1 permit 10.48.0.0 0.0.0.254
access-list 1 permit 10.48.0.0 0.0.0.255
| | 5 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
