| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| LAN stands for which of the following?
A.) Local Area Network
B.) Local Arena Network
C.) Local Area News
D.) Logical Area Network | | 4 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 2 |
| Which configuration mode and command combination sets the
bandwidth metric of a Frame Relay connection?
A. router(config)# clock rate 56
B. router(config)# bandwidth 56
C. router(config)# bandwidth 56000
D. router(config)# clock rate 56000 | | 2 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecing to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecing to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which IEEE standard is used to define Wi-Fi?
A. IEEE 802.3
B. IEEE 802.5
C. IEEE 802.11h
D. IEEE 802.11c
E. IEEE 802.11 | | 1 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 3 |
| Which layer is responsible for synchronizing sending and
receiving
applications?
A.) Presentation
B.) Session
C.) Transport
D.) Application
E.) Network | | 1 |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 2 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| The ICMP (referred to in RFC 1700) is implented by all
TCP/IP hosts.
A. true
B. false | | 1 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 2 |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| which term use to allow user to conect the remote n/w with
ppp dail up conection
ras
sap
sonet
mane answer rsa | | 1 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 1 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
