| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following provide connection-oriented transport to
upper layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| Why we choose the router rather then L-3 Switch | Network-Solutions | 7 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| Using the TCP/IP protocol suite, a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of a MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses PARP requests
D. It uses a router lookup table | | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| Which device works at the Network Layer of the OSI model?
Router
Switch
Bridge
Hub
| | 3 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| what is nat.types of nat | | 3 |
| Which of the following is an example of the Datalink Layer?
A.) LLC
B.) TCP
C.) SQL
D.) IPX
E.) Token Ring
F.) MAC | | 2 |
| The administrator of a comapny needs to ensure that a web
server in
their network is accessible from the Internet. Since the
network uses private
addressing, this requires an IP-to-registered-address
mapping. The following
command is entered on the router:
router(config)# ip nat inside source static 192.168.2.1
198.18.1.254
After unsuccessful results from a ping to the Internet, the
administrator issues the
show ip nat translations command and the output is blank.
What could be the
problem with the NAT configuration for this mapping?
A. The keyword overload is missing from the command.
B. The administrator needs to define a NAT pool first.
C. An access list must be defined to create static NAT
translations.
D. The interfaces need to be configured for NAT. | | 4 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| Which of the following are examples of ICMP?
A.) Traceroute
B.) Web Browsing
C.) Ping
D.) Telnet
E.) Destination Unreachable message from a router
F.) Inverse Tunnels | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
