| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Select the correct statements about PPP and SLIP for WAN
communications?
A. PPP uses its Network Control Programs (NCPs) component to
encapsulate
multiple protocols.
B. PPP can only transport TCP/IP
C. SLIP can only transport TCP/IP.
D. SLIP uses its Network Control Programs (NCPs) component to
encapsulate multiple protocols. | | 1 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 2 |
| You need to come up with a TCP/IP addressing scheme for your
company. How many network IDs must you allow for when you
define the
subnet mask for the network?
A.) One for each WAN link
B.) One for each router interface
C.) One for each NIC installed in each client
D.) One for each subnet with hosts
E.) One for each host ID | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| There is a process in Frame-Relay where LMI resolves an IP
address
from a DLCI number. What is this called?
A.) arp
B.) inverse arp
C.) rarp
D.) automap
E.) reverse arp
F.) arp | | 1 |
| Novell NetWare has an Ethernet frame type called Ethernet_802.2.
What is the matching Cisco command line keyword for this
encapsulation
method?
A.) gns
B.) arpa
C.) snap
D.) sap
E.) novell-ether
F.) dix | | 1 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| Which of the following is a characteristic of a switch, but
not of a
router?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | | 2 |
| Select the physical interfaces that PPP can be configured on
a Cisco
router:
A. Asynchronous serial
B. HSSI
C. ISDN
D. Synchronous serial | | 1 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| Identify 2 characteristics of PPP?
A.) Uses LLC to establish the link
B.) Default serial encapsulation
C.) Support multiple layer 3 protocols
D.) Offers two types of authentication; PAP and CHAP | | 3 |
| Your network is having IP problems connecting to one or more
Frame Relay peer routers. Which two commmands should you
use to show the routers that are reachable? (Choose two)
A. show ip map
B. show ip router
C. show frame-relay map
D. debug frame-relay map | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to do
it | | 1 |
| what is unike ip address | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 2 |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
