| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| What command do you use to disable domain lookup?
A.) no domain-lookup
B.) domain no-lookup
C.) lookup no-domain
D.) no ip domain-lookup | | 2 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| Which three devices can be used to convert the user data
from the
DTE into a form acceptable to the WAN service's facility?
A. Modem
B. CSU/DSU
C. TA/NT1
D. CO
E. SS7 | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| Which technologies listed below help prevent network loops in a
switched (bridged) environment?
A.) Store-and-Forward
B.) IEEE 802.1d
C.) Diikjstra Algorithm
D.) Cut-Through
E.) Spanning Tree Protocol
F.) Routing | | 1 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 2 |
| What is masking? why is needed? | | 4 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| Which of the following is an example of the Network Layer?
A.) LLC
B.) SQL
C.) Token Ring
D.) IPX
E.) SPX | | 1 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 2 |
| Which command verifies encapsulation as well as Layer 1 and
Layer 2 statistics on a router configured for Frame Relay?
A. show ip
B. show interface
C. show statistics
D. show frame-relay | | 1 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Pause-and -forward
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 2 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| You are a network administrator and have been assigned the
IP address of 201.222.5.0. You need to have 20 subnets with
5 hosts per subnet. What subnet mask will you use?
A. 255.255.255.248
B. 255.255.255.128
C. 255.255.255.192
D. 255.255.255.240 | | 2 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| |
| For more CCNA Interview Questions Click Here |