ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3141)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3304)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13466)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2392)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (423)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (80)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (166)
 Instrumentation interview questions  Instrumentation Interview Questions (2407)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (107)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (45)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (81)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1204)
Question
IS HI-POT TEST DONE ON A TRANSFORMER - YES OR NO?
WHY?
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
yes we have to check the insulation helthyness and leakage
current of the insulation.at the time of hipot suppose ur
doing hipot for HV LV should be shortedand earthed that
time we can get healthyness of insulation of the transformer
 
Is This Answer Correct ?    11 Yes 4 No
Gunasekaran
 
Answer
# 2
Most of the transformer companies and testing centres in
india and abroad does not perform this test often,only
during extreme circumstances because this test causes stress
on insulation system due to high voltage which may lead to
windings burn out and transformer failure.
 
Is This Answer Correct ?    6 Yes 1 No
Ars326
 
 
 
Answer
# 3
Yes. Hi-Pot is short for High Potential (Voltage) which
can be deadly if it leaks from the transformer. The test
itself is to see if the insulation of the transformer is
adequate considering the voltage involved. High voltage
transformers such as those little ones in Switch Mode power
supplies also are tested. Google HiPot and see all the
equipment available for this type testing
 
Is This Answer Correct ?    2 Yes 0 No
Erick
 
Answer
# 4
No.
 
Is This Answer Correct ?    4 Yes 8 No
Krupa
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
In directional earth fault protection for generator, one core balance CT is for residual current, what other CT is for, which is placed on neutral?   1
Why we need to carry out knee point voltage test of current transformer ? Power-Grid 1
why the Parameters : Base Voltage & Maximum Voltage can't be equal in value in a VFD (Variable Frequency Drive) ? How much the base voltage would be lower than the maximum voltage ? If 400 V is the 3 phase output of a VFD ... then what should be the base voltage ? thanks a lot Yaskawa 1
DG drop how much freqency at 100% load?   3
What is working Priniciple of TVSS ???? Emerson 1
if the supply voltage increased by N times, the x-section of conductor will be......... APGenco 2
why HT line voltage is multiple of 11.eg11kva,33kva,132kva HP 2
why we use DO Fuse in H.T. Line ? What is the purpose of DO Fuse   3
in Megger what type of voltage(AC or DC) are produce.how they work.   1
Can you any one explain different between instantaneous over current and IDMT   1
what is the use of reactive power   3
will a transformer work when pulsating dc id applied to its primary?? what will be the result?? cemp 1
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com