ok this is practical senario question how can we comunicate two diffrent

Advertise your Business Here

Refer this Site

Login | Sign Up


	SiteMap shows list of All Categories in this site.

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

ok this is practical senario question

how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command

answer is so simple i wiil; give the answer after 20 visit

til then wait

Question Submitted By :: Jitendera Sinha

I also faced this Question!!

Rank

Answer Posted By

Re: ok this is practical senario question how can we comunicate two diffrent network host by i single 1603 sires of cisco router rember that the cisco series of that router have singe 100mbps ethernet now think think write all command answer is so simple i wiil; give the answer after 20 visit til then wait

Answer
# 1

ok i ma giving hint
HINT-# configure sdcondry ip address.its enough ?
no then plz post hint

Is This Answer Correct ?

0 Yes

0 No

Jitu

Answer
# 2

router(config)#interface e0
              #ip address x.x.x.x y.y.y.y(NEtmask=Y)
              #no shut
              #exit
rouetr(config)#interface e0
              #ip address a.a.a.a b.b.b.b secondry
              #no shut
              #exit
router(config)#now from here you can apply your route
according to your network scenario.
but not forget to advertise secondary ip address on the
routing table

Is This Answer Correct ?

1 Yes

0 No

Jitendera Kuamr Sinha

Question	Asked @	Answers
Other CCNA Interview Questions


IP standard access lists use which of the following as a basis for permitting or denying packets? A.) destination address B.) port C.) protocol D.) source address		2
How do you view the routers current processor utilization? A.) show version B.) show processes cpu C.) show running-config D.) show startup-config E.) show cpu F.) show utilization	Cisco	2
Identify the default serial encapsulation? A.) ISDN B.) HDLC C.) SDLC D.) Frame Relay E.) PPP		2
Which range of possible numbers do standard ipx access lists have? A. 100 199 B. 600 699 C. 800 899 D. 1000-1099		1
Identify the default IPX serial encapsulation? A.) Novell-Ether B.) SDLC C.) SNAP D.) HDLC		1
What is an advantage of LAN segmentation? A.) Increases broadcasts. B.) Increases collisions. C.) Provides more protocol support. D.) Decreases broadcasts. E.) Routing protocol support.	Wipro	2
What is the default size of a standard ping on a Cisco router? * A: 100 bytes * B: 32 bytes * C: 10 bytes * D: 16 bytes	CMS	2
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface		1
What should be the first command to create an access-list that prevents all users on subnetwork 10.10.128.0, using subnet mask 255.255.192.0, from being able to telnet anywhere? A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq telnet B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq telnet C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any eq telnet D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq telnet E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq telnet F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq telnet		3
Identify 2 transport layer protocols? A.) IP B.) TCP C.) CDP D.) ARP E.) UDP		2
How would you set the clock rate to 64K, on interface serial 0, from the interface configuration mode? A.) clock rate 64000 B.) bandwidth 64 C.) clock 64 D.) rate 64 E.) clock rate 64k F.) clock rate 64		1
What is ISR or NonISR router? Difference between ISR or NonISR router?	HCL	3
7. What is an advantage to using switches in your network? A. Addressing of hosts by DHCP B. Ease of administration C. Stops broadcast storms D. Works like a repeater	iGate	2
What is the command to start IP RIP version 1 routing on a Cisco router? A. show rip B. enable rip C. router enable D. router rip		5
What is CSU/DSU & explain the function????	Cisco	3
In regards to the OSI seven-layer model, at which layer is EBCDIC and ASCII? A.) Presentation B.) Application C.) Transport D.) Session E.) Datalink F.) Network		1
Which of the following are characteristics of UDP? A.) UDP is connection oriented. B.) UDP is used with TFTP. C.) UDP is unreliable. D.) UDP is connectionless. E.) UDP is at the transport layer. F.) UDP uses no acknowledgements.		4
Which OSI layer performs code conversion, code formatting and encryption? A.) Physical B.) Data-Link C.) Application D.) Transport E.) Presentation F.) Network		1
Your network uses a Class C address of 210.10.10.0. You must now split up the network into separate shores to handle multiple buildings separated by routers. Which two steps must you take to determine the proper shored mask for your networks? (Choose two) A. determine the number of seperate networks required B. determine how many devices will require DHCP addressing C. determine the maximum number of hosts that will be on each shored D. determine the miniumum number of hosts that will be on each shored E. determine which router will be the IP default gateway for each shored		1
Which statement should you use to deny FTP access (only) from network 210 93 105 0 to network 223 8 151 0? A. access list 1 deny 210 93 105 0 0 0 0 0 any eq ftp access list 1 permit any B. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151 0 0 0 0 255 eq ftp C. access list 100 deny ip 223 8 151 0 0 0 0 255 any eq ftp access list 100 permit hp any any D. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151 0 0 0 0 255 eq ftp access list 100 permit ip any any		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com