| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How many Frame-relay encapsulation types are available with
Cisco
routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 2 |
| what are the 3ree way for implementing vlan on cisco switches
what is the layer hierarchy of the cisco
what is the best place of implementing standard access list
what is q stand for isdn
these are the challanging question for me
i am waiting for jitendera sinha answer(it is challenge for
u i have seen lots of answer given by u )it is a challenge
in the frendshipmode plz donot take other wise
| | 2 |
| When setting up a WAN network, everything outside of the
Demarc is
not owned by the customer. Which of the following are not
owned by the
customer?
A.) The T1 line.
B.) LAN
C.) The Router
D.) DTE
E.) PC's
F.) CO | | 1 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 2 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| what is the distance betwwen link stae routing protocl and
distance vector
who have the best convergence toplogy
eigrp conatain 3 table name them
what the toplogy table contain | IBM | 5 |
| what is the default ad value of the interface directly
coneted to router.
as for exmaple ad value of ospf is 90 then from ehternet
the network is conected whta is difault value of that
directly conected interface.
what is the defalt ad value of bgp
whta is access llist and how many type of access list
what is vlan
what is vpn
how e congigure the router
what is mpls
these are the question skrd to me at tcs i have replyed all
ecxept the first one
| TCS | 1 |
| take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
| AT&T | 6 |
| why we give clock rate to DCE and not to DTE
what is the difference in the two. | | 2 |
| Which three commands are used to configure information into
RAM on a router? (Choose three)
A. configure memory
B. configure terminal
C. configure overwrite
D. copy tftp startup-config
E. copy running-config startup-config
F. copy startup-config running-config | HCL | 5 |
| What is Cisco register bits? How they help? | jetking | 1 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future? | | 3 |
| Which command line option will determine what traffic is
interesting enough to establish a dialup connection?
A.) dialer map
B.) dialer string
C.) dialer in-band
D.) dialer-list
E.) dialer negotiation | | 1 |
| Which layer is responsible for flow control,
acknowledgement, and
windowing?
A.) Transport
B.) Network
C.) Application
D.) Session
E.) Physical
F.) Data Link | | 2 |
| What are the two most common request/reply pair with ICMP
messages when using the ping command? (Choose two)
A. echo reply
B. echo request
C. source quench
D. fragment onset
E. information redirect
F. destination reachable
G. echo control message | | 1 |
| Which device listed below provides clocking for the line?
A.) DCE
B.) CPE
C.) CO
D.) DTE
E.) Demarc | | 2 |
| What is the most common layer 2 device?
A. Hub
B. Router
C. Switch
D. Repeater | Wipro | 5 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
