no sahin it is not wrong it is correct but that value is
not given in to the option
so i marked it wrong
i think iot may be 7
explantion
scince loopback is 127.0.0.1
so in that frst bit is always off
remanig 7
thus aqll bit are on thus the nuric value of lopback
address might be 7
but but but i am not dam sure this time i am also confused
not little bit much more.so do not get it that it is wright
i am 30%sure that it migh be
How cud u say binary value of 1st octate, coz we know IP
address consist of four octate, each of 8 bits.
XXXXXXXX.XXXXXXXX.XXXXXXXX.XXXXXXXX
I don't think it wud be a justified answer if we say "7".
coz he is nt asking the binary bit of first octate. so we hv
to take or assume the conventional 4 octate criteria.
Hi.. Jitendera, this may open up some more question.
heheheheh..!!!!
actualr sahin
my argue based on that consept
that is loop back address is 127.0.0.1
let consider its wild mask that is
0.255.255.255
that is match exct value of 1st octaet and three octet may
have value
try to ping 127.4.5.6
u will get reply through 127.0.0.1
ok that is 127 n/w bit is resved for the nic card
functionaly staus and we refred as it loop back address
now
scinselast three octet have any value then we are not aware
of that
scine first octet is fix for n/w id 127
then
from our most convanonal rule
128 64 32 16 8 4 2 1
0 1 1 1 1 1 1 1=127 that is 7 bit
scince that was in option so i mark it
i know u r corect but that option are not present in answer
sheet
and i am not bale to write that opton on answer sheet and
then mark
ha a ha haaaa
so i apply my wrong/wright consept and mark 7
i donot know it was wright or not so i placed it on all
interview .com
Hi Jitendera, for ur concern, next time write the complete
question. Heheheh
If the option were written in question thn specify it in
posting yaar..!!!
According ur option u r right.
Don't mind..!!! C ya..!! Keep posting..!!
Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame
Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe
How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run
Identify 3 characteristics of a connection oriented protocol?
A.) Path determination
B.) Flow control
C.) Acknowledgements
D.) Uses hop count as metric
E.) 3 way handshake
What is the protocol and what is the purpose of the
following address?
238 255 255 255
A. IPX a SAP broadcast
B. IP a multicast group
C. IP a reserved address
D. IP a directed broadcast
E. IPX a flooded broadcast
Identify the command to copy a configuration file from a TFTP
server to a routers active configuration?
A.) Router# copy running-config tftp
B.) Router# copy tftp running-config
C.) Router# copy tftp 172.16.0.1 running-config
D.) Router(config)# copy tftp running-config
Which two statements about the store and forward switching
method are true? (Choose two)
A. Latency remains constant regardless of frame size.
B. Latency through the switch varies with frame length.
C. The switch receives the complete frame before forwarding it.
D. The switch checks the destination address as soon as it
receives the header and begins forwarding the fram immediately.
Which of the following can reply to a Novell Get Nearest
Server (GNS)
request?
A.) Local Novell server
B.) Remote Novell Printer
C.) Cisco router
D.) Novell client
Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured
You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp
What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency.
Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department
The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full
You want to enable both arpa and snap encapsulation on one
router interface. How do you do this?
A. The interface can handle multiple encapsulation types
with no extra configuration.
B. Assign two network numbers, one for each encapsulation
type.
C. Enable Novell-ether to run multiple encapsulation types.
D. Both arpa and snap are enabled by default so you don't
have to configure anything.
Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic
along with your userid / name. ThanQ
Site Map
