take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Answers:-
A & E:- Both the questions are contradictory.
B:- Host can access the command prompt anyway.
C:- Network Admin already permitted SW2 host to
access the router through telnet.
D:- Depends on the Network Admin whom he wants to
give access to internet.
F:- I think RIP routing protocol should be configured
for access.
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
no monoj corect answer is given
B
but the expalantiom is not given so i am not agree with
that answer
if you have some expalnation about answer b then plz write.
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Configuration -
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
Ra(config)#access-class 2 in
From the above configuration one thing is clear that only
host from 10.1.1.0 network (i.e Switch 2)can access the telnet.
Host from 10.1.2.0 network are not allowed to access the
TELNET. As the access list specified on vitual terminal ie.
line vty 0 4.
So [B] is the correct answer.
[B] To prevent sw1 host from accessing command prompt
I configure ur scenario in PACKET TRACER & configure
accordingly.
After that i tried to access TELNET from client of Switch2,
i wz successful. Ie. Router allow to access the TELNET.
After that i tried to access TELNET from client of Switch1,
i wzn't successful.Ie Router doesn't allow to access the TELNET.
On the option, it create little bit confusion on mind..
COMMAND PROMPT of which device... off course its ROUTER.
If the option were written in specific, than i think no
confusion will arise.
I hope, it will help u..!!
Let me know my feedback..!!
thanxx for such a gud question.
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Configuration -
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
Ra(config)#access-class 2 in
From the above configuration one thing is clear that only
host from 10.1.1.0 network (i.e Switch 2)can access the telnet.
Host from 10.1.2.0 network are not allowed to access the
TELNET. As the access list specified on vitual terminal ie.
line vty 0 4.
So [B] is the correct answer.
[B] To prevent sw1 host from accessing command prompt
I configure ur scenario in PACKET TRACER & configure
accordingly.
After that i tried to access TELNET from client of Switch2,
i wz successful. Ie. Router allow to access the TELNET.
After that i tried to access TELNET from client of Switch1,
i wzn't successful.Ie Router doesn't allow to access the TELNET.
On the option, it create little bit confusion on mind..
COMMAND PROMPT of which device... off course its ROUTER.
If the option were written in specific, than i think no
confusion will arise.
I hope, it will help u..!!
Let me know my feedback..!!
thanxx for such a gud question.
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Re: take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
Check it out in packet tracer & let me knw...!!! If u r
unable to do the telnet of router from client command
prompt, thn ultimately u r unable to access the command
prompt of router as well.
U cn access the client command prompt as ur requirement, but
not router's command prompt.
Which three commands are used to configure information into
RAM on a router? (Choose three)
A. configure memory
B. configure terminal
C. configure overwrite
D. copy tftp startup-config
E. copy running-config startup-config
F. copy startup-config running-config
Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in
Why do we have a Layered Model?
1) It reduces complexity
2) Allows for a standardized interface
3) Facilitates modular engineering
4) Ensures interoperable technology
5) Accelerates evolution
6) Simplifies teaching and learning
8. When is Frame Tagging used?
A. When you install repeaters in your network
B. When you install bridges in your network
C. When you install routers in your network
D. When you use Switches configured with multiple VLANS
there is three mode of vtp let there are three switch s1 in
server mode s2 in transparent mede and s3 in clint mode
then will that tranparnt mode going to effect the network if
yes then how and if no then what it will do
What does the Frame Relay switch use to distinguish between
each PVC connection?
A. data-link connection identifiers (DLCIs)
B. BECNs
C. FECNs
D. the Local Management Interface (LMI)
Routers can learn about destinations through static routes,
default, or dynamic routing. By default, a router will use
information derived from __________.
A. IGRP
B. RIP
C. IP
D. TCP
Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address
Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously
Which element is used to define the rate in bits per second
that a Frame Relay switch agrees to transfer data?
A. clock rate (CP)
B. Committed Information Rate (CIR)
C. Local Management Interface (LMI)
D. data link connection identifier (DICI)
E. Committed Rate Measurement Intercal (CRIMI)
What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards
Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24
Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection
Cisco routers can secure the enable password with a one-way hash
algorithm. What command would encrypt the enable password
with the
strong encryption method?
A.) enable encrypt john
B.) password john
C.) enable secret john
D.) enable password john
E.) secret john
F.) enable password 5 john
Site Map
