| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which command listed below sets the banner message when someone
connects to the router?
A.) message #
B.) banner #
C.) login banner #
D.) description #
E.) login description #
F.) banner motd # | | 2 |
| Identify the true statement regarding subnetting?
A.) Allows for more host address
B.) Borrow bits from the network portion of the address
C.) Allows for unlimited number of networks
D.) Borrow bits from the host portion of the address | | 1 |
| Which command assigns the login password CISCO on the
console terminal line?
A. line vty 0 login password cisco
B. line console login password cisco
C. line login terminal password cisco
D. line console 0 login
E. line console 0 login password cisco | | 2 |
| Identify 3 characteristics of a connection oriented protocol?
A.) Path determination
B.) Flow control
C.) Acknowledgements
D.) Uses hop count as metric
E.) 3 step handshake | | 2 |
| Scenario: You created 2 access-lists for controlling telnet
about
a year ago, and bound one of them to Serial 0. You can't
remember which
access-list you
used. Which command lets you see all access-lists on Serial
0 for telnet?
A.) show access-list
B.) show ip int s0
C.) show access-list telnet
D.) show telnet access-list
E.) show access-list s0
F.) show int s0 | | 2 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| How many valid host IP addresses are available on the
following network/subnetwork? 176.12.44.161/30
A. 2
B. 30
C. 254
D. 16,382
E. 65,534 | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | Barnes-and-Noble | 2 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Identify the switching method that examines the destination MAC
address as
the frame is being received then begins forwarding the frame
prior to
receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| tell me our traditional ip routing is what
A--conectless
b----conection orented
c-----pacekt switching
d------ckt switching
slect any two
this is the question which i forgot to incoprate
next-questions
| | 3 |
| Identify 1 characteristic of RARP?
A.) IP to MAC address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 2 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Which two steps are required to confound and apply standard
access lists on an interface? (Choose two)
A. define an access list number and its parameters
B. enable an interface to become part of the access list group
C. define the number of access lists to be supported on an
interface
D. copy the access list definition to each interface that
will support it | | 2 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of
the connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
