| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Hi,can anyone explain me in brief about ccna security.
waiting for your answer | | 2 |
| Which two statements about the store and forward switching
method are true? (Choose two)
A. Latency remains constant regardless of frame size.
B. Latency through the switch varies with frame length.
C. The switch receives the complete frame before forwarding it.
D. The switch checks the destination address as soon as it
receives the header and begins forwarding the fram immediately. | | 1 |
| When setting up a frame-relay network between a Cisco router
and a
non-Cisco router, what encapsulation type should you use?
A.) SAP
B.) CISCO
C.) IANA
D.) Apollo
E.) IETF
F.) Q933A | | 1 |
| bWhich form of PPP error detection on Cisco routers monitors
data
dropped on a link?
A. Quality
B. Magic Number
C. Error Monitor
D. Droplink | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 4 |
| Which two physical interfaces support PPP? (Choose two)
A. Ethernet
B. Token Ring
C. Synchronous serial
D. Asynchronous serial | | 1 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| Which ISDN specification series deals with Concepts and
Terminology?
A.) World Series
B.) I- Series
C.) Q-Series
D.) 911-Series
E.) J-Series
F.) F-Series | | 1 |
| Which protocol works at the Internet layer and is
responsible for
making
routing decisions?
A.) UDP
B.) IP
C.) TCP
D.) ARP | | 3 |
| Scenario: You created 2 access-lists for controlling telnet
about
a year ago, and bound one of them to Serial 0. You can't
remember which
access-list you
used. Which command lets you see all access-lists on Serial
0 for telnet?
A.) show access-list
B.) show ip int s0
C.) show access-list telnet
D.) show telnet access-list
E.) show access-list s0
F.) show int s0 | | 2 |
| You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp | | 2 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 3 |
| Which command listed below sets the banner message when someone
connects to the router?
A.) message #
B.) banner #
C.) login banner #
D.) description #
E.) login description #
F.) banner motd # | | 1 |
| Layer 1 and Layer 2 devices must forward a broadcast.
Which of the following devices fall into this category?
Gateway
Switch
Router
All of the above.
| | 1 |
| IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port | | 1 |
| what is hop count? | | 11 |
| Which show command should you use to view Frame Relay Local
Management Interface (LMI) Frame statistics?
A. show lmi
B. show ip route
C. show interface
D. show statistics
E. show frame-relay lmi | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
