| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the difference between switch and router?? | Thomson | 7 |
| Which show underrate serial 1 status statement indicates
that the shutdown command was issued on that interface?
A. Serial 1 is up line protocol is up
B. Serial 1 is up line protocol is down
C. Serial 1 is down line protocol is down
D. Serial 1 is administratively down the line protocol is down | Pioneer-Labs | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | Infosys | 3 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| What is true about frame-relay DLCI?
A.) DLCI represents a single physical circuit
B.) DLCI is optional in all frame-relay networks
C.) DLCI identifies a logical connection between DTE devices
D.) DLCI is used to tag the beginning of a frame with VLAN
information | | 1 |
| WHAT IS SERIAL TRANSMISSIONS,PARALLELL TRANSMISSION | ASD-Lab | 2 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| Which command, that is used to test address configuration,
uses Time-To-Live (TTL) values to generate messages from
each router.
A. trace
B. ping
C. telnet
D. bootp | | 1 |
| How many valid host IP addresses are available on the
following network/subnetwork? 176.12.44.161/30
A. 2
B. 30
C. 254
D. 16,382
E. 65,534 | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 1 |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| The "ipx delay number" command will allow an administrator to
change the default settings. What are the default settings?
A. For LAN interfaces, one tick; for WAN interfaces, six
ticks
B. For LAN interfaces, six ticks; for WAN interfaces, one
tick
C. For LAN interfaces, zero ticks; for WAN interfaces, five
ticks
D. For LAN interfaces, five ticks; for WAN interfaces, zero
Ticks | | 1 |
| Which command can verify Application Layer connectivity
between 2
hosts?
A.) ftp
B.) snmp
C.) telnet
D.) ping
E.) traceroute | | 2 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| What’s the default CDP holdtime in seconds for Cisco routers?
| | 2 |
| If a frame is received at a switch and only the destination
hardware address is read before the frame is forwarded, what
type of
switching method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| What is BGP attribute & How many types of attributes are
used by BGP??? | Hathway | 3 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | IIHT | 3 |
| Choose the following that are benefits to segmenting with
router:
A.) Flow Control
B.) Manageability
C.) Multiple Active Paths
D.) Explicit packet lifetime control | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
