ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3010)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3270)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13221)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2348)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (407)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (76)
 Bio Engineering interview questions  Bio Engineering Interview Questions (16)
 Metallurgy interview questions  Metallurgy Interview Questions (79)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (162)
 Instrumentation interview questions  Instrumentation Interview Questions (2317)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (104)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (43)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (73)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1189)
Question
What is the function of stater in tube light circuit?
 Question Submitted By :: My.selection
I also faced this Question!!     Rank Answer Posted By  
 
  Re: What is the function of stater in tube light circuit?
Answer
# 1
Tube light requires two things to function . Very high starting voltage , and high voltage to continue the operation . The starter is a circuit which breaks at regular intervals . When you break a circuit and start again , high voltage spark takes place . This voltage is further amplified through the choke which is a transformer . Thus at the beginning the starter gives high voltage sparks . Due to this the current begins to flow through the tube and the tube begins to glow. Once the tube starts , the required voltage to sustain is quite low , which is provided by the choke .

If the starter is bad the tube does not start . If the choke is bad or if the gas is low , the tube does not sustain its light .
 
Is This Answer Correct ?    6 Yes 8 No
Bhanu Pratap
 
  Re: What is the function of stater in tube light circuit?
Answer
# 2
The starter is basically a time delay switch. Its job is to
let the current flow through to the electrodes at each end
of the tube, causing the filaments to heat up and create a
cloud of electrons inside the tube. The starter then opens
after a second or two. The voltage across the tube allows a
stream of electrons to flow across the tube and ionize the
mercury vapor.
Without the starter, a steady stream of electrons is never
created between the two filaments, and the lamp flickers.
 
Is This Answer Correct ?    7 Yes 2 No
Karthik
 
 
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
What is the relation of current with torque when motor started in Y-connection???   4
What is BKW of Motor. And what its significance Thermax 1
AP Transco Assistant Engineer (Electrical) Model Question papers APTransco 2
I have a question, I visit 01 site and face a problem, there is 2.5 ton Air Con working, when air con compressor is running at that time rectifier voltages are increasing upto 290-295 v and rectifier is giving main high alarm (rectifier is APC single phase), before starting compressor rectifier voltages was 230v. when air con is going off rectifier voltages are decreasing smoothly at its actual voltages 230v. Load on Genset phases is this: Red-13.5 amp AC (Air Con load), Yellow-1.7 amp AC (BTS lights etc.) and Blew-4 amp AC (telecom system load), Genset phase to phase and neutral to phase voltages are also ok. These are 10 sites having same system and same rectifier APC brand at every site 02 genset are working but the problem is same at all these 10 sites. What will be the reason behind???   1
Alternators are invariably star connected why?   4
define electrical field? L&T 6
is there or does RCCB work for single phase connection?   1
Why C.T secondary s2 done earthing?   4
when we start the tube light, then it takes initially 1100 volt, after glow it takes 120 volt?(when we give 220 volt a.c.)   2
why the rating of transformer in only KVA not in others?   6
what is the current rating of 2500 KVA,33KV/433v transformer on secondary(LT) side Reddy-Labs 6
why the field winding of synchronous machine is excited by dc source   2
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com