| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| what is nat.types of nat | | 3 |
| A company running RIP V1 protocol on their 2 seperate
networks, each nw has 14 routers, if the two nw wants to be
merged with each other total no of routers will be 28. but
rip metric is hop count(15). What needs to be done if this
setup needs to be work ? | Satyam | 2 |
| To prevent Service Advertisements (SAPs) from flooding a
network, Cisco routers do not forward them. How are
services advertised to other networks?
A. Each router builds its own SAP table and forwards that
every 60 seconds.
B. Each router assigns a service number and broadcasts
that.
C. SAPs aren't necessary with Cisco routers.
D. Cisco routers filter out all SAPs. | | 1 |
| Identify the OSI layer which is responsible for end-to-end
connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 2 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| Hi Gyes, here is new question. can you provide answer of
following question
Like linux, can we windows as router?
If yes how can we able to do this, | | 2 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 2 |
| mention the funtions about connection oriented and
connectionless protocol and how it works ? | | 4 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| Which Cisco IOS command should you use to display the Novell
IPX address assignments on a router?
A. show ipx addresses
B. show ipx interface
C. show me the money
D. ipx, network (number)
E. display ipx addresses
F. show ipx routing details | | 1 |
| Which of the following is a characteristic of a switch, but
not of a
router?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 1 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 2 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only 4 encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.2 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encapsulation must be configured unless the
connecting routers
are both
Cisco | | 1 |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip | | 5 |
| Your PC has been configured with IP Address 192.168.3.25
and a subnet mask of 255.255.255.0. Which of the following
IP Addresses is a valid default gateway address for your
PC?
192.168.3.0 255.255.255.0
192.168.3.2 255.255.255.0
192.168.3.25 255.255.255.0
192.168.4.1 255.255.255.255
| | 1 |
| Why Authentication Header (AH) is not compatible with the
network that using NAT??????
Jitu, looking for u specially...!!!! U knw why i m looking
for u..!!! | | 1 |
| Which element is used to define the rate in bits per second
that a Frame Relay switch agrees to transfer data?
A. clock rate (CP)
B. Committed Information Rate (CIR)
C. Local Management Interface (LMI)
D. data link connection identifier (DICI)
E. Committed Rate Measurement Intercal (CRIMI) | | 1 |
| |
| For more CCNA Interview Questions Click Here |