| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which layer allows multiple Ethernet devices to uniquely
identify
one another on the Datalink layer?
A.) Transport
B.) Session
C.) Network
D.) Datalink - MAC Sublayer
E.) Datalink - LLC Sublayer | | 3 |
| When determining whether or not to route a LAN segment,
which rule of
thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| Which device listed below provides clocking for the line?
A.) DCE
B.) CPE
C.) CO
D.) DTE
E.) Demarc | | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol? | | 1 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Which of the following are Distance Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 3 |
| what is nat.types of nat | | 3 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 1 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash
B.) boot system flash IOS_filename
C.) boot system IOS_filename flash
D.) boot system tftp IOS_filename tftp_address
E.) config-register 0x0102 IOS_ filename | HSBC | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| The "ipx delay number" command will allow an administrator to
change the default settings. What are the default settings?
A. For LAN interfaces, one tick; for WAN interfaces, six
ticks
B. For LAN interfaces, six ticks; for WAN interfaces, one
tick
C. For LAN interfaces, zero ticks; for WAN interfaces, five
ticks
D. For LAN interfaces, five ticks; for WAN interfaces, zero
Ticks | | 1 |
| Select the fields for the Cisco HDLC protocol:
A. Flag, Address, Control
B. Flag, Address, Control, Protocol, LCP (Code, Identifier,
Length,
Data), FCS, Flag
C. Flag, Address, Control, Data, FCS, Flag
D. Flag, Address, Control, Proprietary, Data, FCS, Flag | | 1 |
| Which network mask should you place on a Class C address to
accommodate a user requirement for five networks with a
maximum of 17 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 7 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 1 |
| Which layer of the 7 layer model is responsible for
representing the
application information between 2 different OS's? For
example, converting
ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
