| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| PLACE YOURS QUESTION HERE I ALSWYS BE HERE FROM 9 AM TO 6PM SO
U CAN FIND YOUR ANSWER QUICKLY.IF I KNOW THEN ?
JJIITTEENNDDEERRAA SSIINNHHAA | | 4 |
| Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from
telneting
B.) This access list prevents any telnet traffic from subnet
192.10.172.0/24
C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet
192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed | | 1 |
| Which two statements about the store and forward switching
method are true? (Choose two)
A. Latency remains constant regardless of frame size.
B. Latency through the switch varies with frame length.
C. The switch receives the complete frame before forwarding it.
D. The switch checks the destination address as soon as it
receives the header and begins forwarding the fram immediately. | | 1 |
| When using access lists, it is important where those access
lists
are placed. Which statement best describes access list
placement?
A. Put standard access lists as near the destination as
possible. Put
extended access lists as close to the source as possible.
B. Put extended access lists as near the destination as
possible. Put
standard access lists as close to the source as possible.
C. It isn't import where access lists are placed since the
router will
read and cache the whole list.
D. Put access lists as close to corporate headquarters as
possible. | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 1 |
| NetWare IPX addressing uses a network number and a node
number. Which statements are true?
A. The network address is administratively assigned and can
be up to 16 hexadecimal digits long.
B. The node address is always administratively assigned.
C. The node address is usually the MAC address.
D. If the MAC address is used as the node address, then IPX
eliminates the use of ARP. | | 1 |
| What is the most common layer 2 device?
A. Hub
B. Bridge
C. Switch
D. Router | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a
Frame Relay network, which encapsulation type would you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| as we know that isdn bri port come with either a u
interface or some thing s/t interface what is the
diffrenmce between them | HCL | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0
255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how it
can be reached via 10.1.0.1
D.) Assigining the IP address 192.168.100.0 to an interface | | 1 |
| How many access lists are allowed per interface?
A. One per port, per protocol
B. Two per port, per protocol
C. Unlimited
D. Router interface +1 per port. | | 2 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Autonomous system number
E.) Link state | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 2 |
| Station A is transmitting data to station B, and expects an
acknowledgment
after every 400 bytes. After transmitting data for a while,
the two
stations determine the line is reliable and change to
expecting and
acknowledgement every 600 bytes.
This is an example of (pick the best answer only):
A.) BECN
B.) Sliding Windows
C.) Poison Reverse
D.) Countdown timers
E.) Split Horizon
F.) Count to infinity | | 1 |
| Identify the OSI layer associated with bits?
A.) Physical
B.) Network
C.) Binary
D.) Data link | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| what are the 3ree way for implementing vlan on cisco switches
what is the layer hierarchy of the cisco
what is the best place of implementing standard access list
what is q stand for isdn
these are the challanging question for me
i am waiting for jitendera sinha answer(it is challenge for
u i have seen lots of answer given by u )it is a challenge
in the frendshipmode plz donot take other wise
| | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
