| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following are examples of the Session Layer?
A.) TCP
B.) RPC
C.) SQL
D.) NFS
E.) Token Ring | | 1 |
| What is the distance limitation for 100BaseT?
A. 305.955 ft
B. 7283.46 inches
C. 184 Meters
D. 185 Kilometers | | 3 |
| In which three situations is a hold down timer reset?
(Choose three)
A. when the hold down timer expires
B. when infinity is finally defined as some maximum number
C. when the router exchanges update summaries at area borders
D. when the router detects faulty LSPs propagating through
the internetwork
E. when another update is received indicating a new route
with a better metric
F. when another update is received indicaing the original
route to the network has been restored
G. when the router receives a processing task proportional
to the number of links in the internetwork | | 1 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| Which command verifies encapsulation as well as Layer 1 and
Layer 2 statistics on a router configured for Frame Relay?
A. show ip
B. show interface
C. show statistics
D. show frame-relay | | 1 |
| Which command-line keywords are valid for choosing
Frame-Relay LMI
types?
A.) itu-t
B.) dlci
C.) ansi
D.) rfc 1544
E.) cisco
F.) q933a | | 1 |
| Which technology is used by Catalyst switches to resolve
topology loops and ensure data flows properly through a
single network path?
A. virtual LANS (VLANS)
B. frame filtering
C. cut-through switching
D. spanning-tree protocol | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 1 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| Which network mask should you place on a Class C address to
accommodate a user requirement for five networks with a
maximum of 17 hosts on each networks
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248 | | 7 |
| What is the command to allow you to type Tokyo instead of the IP
address
172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| what is vc,pvc,lmi and dlsi | | 1 |
| When setting up a WAN network, everything outside of the
Demarc is
not owned by the customer. Which of the following are not
owned by the
customer?
A.) The T1 line.
B.) LAN
C.) The Router
D.) DTE
E.) PC's
F.) CO | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection | | 3 |
| What is the standard ISDN term for a native ISDN modem?
A.) ET
B.) LE
C.) TE2
D.) TE3
E.) TA | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
