| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| Why Authentication Header (AH) is not compatible with the
network that using NAT??????
Jitu, looking for u specially...!!!! U knw why i m looking
for u..!!! | | 1 |
| Which of the following is an example of the Datalink Layer?
A.) LLC
B.) TCP
C.) SQL
D.) IPX
E.) Token Ring
F.) MAC | | 2 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future? | | 3 |
| IPX routing updates occur how often?
A.) Every 30 seconds
B.) Every 60 seconds
C.) Only as needed
D.) When the remote router asks for an update | | 1 |
| router | Infotech | 1 |
| You have a Class B network address divided into 30 subnets. You
will add 25 new subnets within the next year. You need 600
host IDs for
each subnet.
Which subnet mask should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0 | | 1 |
| Which of the following protocols are used to get an IP address
from a known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 1 |
| On Cisco catalyst 5000 how would you set the second port on the
controller in the first slot to full duplex?
A.) Set port duplex 1/1 full
B.) Set port duplex 1/2 full
C.) Set port duplex 0/1 full
D.) Set port duplex 0/2 full | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| Which OSI layer establishes, maintains and terminates sessions
between hosts?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 1 |
| Which IP Address Class can have 64,000 subnets with 64,000
hosts per subnet?
A. Class B
B. Class A
C. Class C
D. Class D | | 2 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| The CSMA/CD Ethernet IEEE committee is defined as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| how to troubleshoot when protocols is down and link is not
getting up | HCL | 5 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
