:: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Categories >> Certifications >> Cisco Certifications >> CCNA


 CCNA interview questions  CCNA Interview Questions (1883)
 CCDA interview questions  CCDA Interview Questions (88)
Which three types of connectors are commonly associated 
with Cisco's V.35 serial cables? (Choose three.)
0 RJ 11
1 DB 60
2 Winchester 15 pin
3 DB 9
4 smart serial
5 RJ 45
 Question Submitted By :: CCNA
I also faced this Question!!     Answer Posted By  
# 1
1 DB 60
2 Winchester 15 pin
4 smart serial
Is This Answer Correct ?    22 Yes 1 No
# 2
1 DB 60
2 Winchester 15 pin
4 smart serial
Is This Answer Correct ?    3 Yes 0 No
# 3
01 db60
04 smart srial
05 rj 45
Is This Answer Correct ?    1 Yes 7 No
# 4

V.35 is a Modem installed on Client location so it requires
the following 3 serial cables

0 RJ11
3 DB 9
5 RJ45
Is This Answer Correct ?    0 Yes 7 No
S.m.feroz Ahmed
# 5
db 9
winchester 15 pin
Is This Answer Correct ?    6 Yes 17 No
# 6
answer is
rj 11
winchiter 15 pin
smart serial
Is This Answer Correct ?    8 Yes 24 No
Jitendera Sinha

Other CCNA Interview Questions
  Question Asked @ Answers
Which Standard IP Access list commands will deny only the source address A.) access-list 9 deny host B.) access-list 9 deny C.) access-list 9 deny D.) access-list 9 deny E.) access-list 9 deny   4
EIGRP send query reply & Acknowledgment on which address ?   3
Which of the follow do not belong to the customer? A.) CO B.) DCE C.) Router D.) CPE E.) Demarc F.) DTE   1
Which of the following are Session Layer standards? A.) ASCII and EBCDIC B.) MPEG and MIDI C.) RPC and SQL D.) JPEG and PICT   3
Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3   1
Which of the following would not be displayed by the command ?sho cdp neighbor detail?? A.) The incoming/outgoing interface. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.   1
A default route is analogous to a _________. A. default gateway B. static route C. dynamic route D. one-way route   1
What is the extended IPX access list range? A.) 901-1000 B.) 100-199 C.) 900-999 D.) 1000-1000   2
Which command displays the intenances using a given access list? A. show filters B. show ip interface C. show active lists D. show interface paramaters E. configure ip access lists F. show access-list interfaces   1
Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Route# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes   1
When you cords an IP address on a place router which command stale the IP processing on the interface? A. ip enable B. network ip-address C. ip address ip-address subnet mask D. the exit command from the enabled configuration E. copy running-configuration to startup-configuration   3
IGRP uses flash updates, poison reverse updates, holddown times, and split horizon. How often does it broadcast its routing table updates? A. 90 seconds B. 10 seconds C. 30 seconds D. 45 seconds   1
For more CCNA Interview Questions Click Here 

Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
Copyright 2013  All Rights Reserved.   ::