| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| Bridges work at what layer of the OSI model?
A.) Data Link
B.) Network
C.) Physical
D.) Application | | 1 |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| Which three protocols are corerectly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Which of the following are ways to provide login access to a
router?
A.) HTTP
B.) Console
C.) Telnet
D.) Aux Port
E.) SNMP
F.) LLC | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 1 |
| What is convergence time?
A.) The update time
B.) The time it takes to reload a router
C.) The time it takes for a packet to reach its destination
D.) The time is takes for all routers update their tables
after a change
takes place | | 1 |
| Which of the following is an example of the Physical Layer?
A.) TCP
B.) ARP
C.) IP
D.) FDDI
E.) LLC
F.) Fast Ethernet | | 2 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| Which command will show you if you have a DTE or DCE
cable connected to an interface? | | 3 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM | HCL | 16 |
| 4. What is a disadvantage to using bridges in your network?
A. Filters by MAC address
B. Stops broadcast storms
C. Doesn't stop broadcast storms
D. Can only use up to 4 bridges in any LAN
| | 2 |
| If i connect two routers through ethernet cable and serial
cable then which has high speed and which is better among
two? | Compaq | 9 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol? | | 1 |
| Novell IPX network addresses have two conferrable parts.
The network administrator specifies the IPX network number.
How is the node number determined?
A. It is the serial number of the given device
B. It is assigned as a lease by Novell DHCP
C. It is also set by the network administrator
D. It is usually the MAC address of one Interface
E. It is downloaded by Netware Core Protocol (NCP) | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
