| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| Identify the purpose of the wildcard mask?
A.) Match a certain portion of the IP address while ignoring
the rest of
the address
B.) Determine the class of the IP address
C.) Determine the network portion of an IP address
D.) Hide the host portion of an IP address | | 1 |
| You are given the IP address of 172.16.2.160 with a subnet
mask of 255.255.0.0. What is the network address in binary?
A. 10101100 00010000
B. 00000010 10100000
C. 10101100 00000000
D. 11100000 11110000 | | 2 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet
interface?
A.) novell-ether
B.) gns
C.) snap
D.) arpa
E.) sap
F.) dix | | 1 |
| Which of the following is an example of the Network Layer?
A.) TCP
B.) IP
C.) SQL
D.) Token Ring
E.) LLC | | 1 |
| Identify the purpose of ICMP?
A.) Avoiding routing loops
B.) Send error and control messages
C.) Transporting routing updates
D.) Collision detection | Hughes | 2 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| hi friends i have a problem.plz solve this.
i am working some where and i have the number of
swtitch.once my project manger says that we are going to
exapnd our number of employ so plz attech an another
switch.i asked to my jr network engineer that take a witch
and implemnt on that n/w,as he implement the switch on that
n/w.thats network get down,
plz tell me what is the reason of that.
| | 1 |
| Hi Guys
I am facing one problem while configuring PAP over Point to
Point links. Configuration scenario is like this.
ROUTER 1: (Hostname – R1)
R1(config)#username R2 password CCNA2
R1(config)#interface serial 1/1
R1(config-if)ip address 10.0.0.1 255.0.0.0
R1(config-if)#lock rate 64000
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication pap
R1(config-if)#ppp pap sent –username R1 password CCNA1
R1(config-if)#no shutdown
ROUTER 2: (Hostname – R2)
R2(config)#usename R1 password CCNA1
R2(config)#interface serial 1/1
R2(config-if)#ip address 10.0.0.2 255.0.0.0
R2(config-if)#encapsulation ppp
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent –username R2 password CCNA2
R2(config-if)#no shutdown
Now problem is that, after configure the command “ppp
authentication pap” the “Line protocol” status goes down on
each router. But when I disable this command using “no ppp
authentication pap”, the “Line Protocol” status goes up.
What could be the problem, can anyone explain it plzzz….!!!
Thanks in Advance…!!
Shahin..
| | 6 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| thnx Jitender singh...as u told to install a stp in switches
and problem vil b get solved...i wanna kno how to install
stp in switches??
plz tel me detailled steps...
thanx for ur answer. | | 1 |
| what is hop count? | | 11 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 2 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 2 |
| You are given the following address: 153.50.6.27/25.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.255.128, B,153.50.6.0, 153.50.6.127
B. 255.255.255.128, C,153.50.6.0, 153.50.6.127
C. 255.255.255.128, C,153.50.6.127, 153.50.6.0
D. 255.255.255.224, C,153.50.6.0, 153.50.6.127 | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
