RIP-It sends complete routing table to all its active
interface in evert 30 seconds.Hold down Timer:-it is a time
during the destination hop is unreachable=240 seconds..
IGRP:-Timer 90 seconds
RIP-30 Sec Periodically
IGRP-90 Sec Periodically
EIGRP-Only if there is a change in network structure.No
periodically
OSPF-Only Either if there is a change in network structure
or 30 Min Whichever is earliar.
RIP,15 seconds.
(RIP Send routing table to all connected routers)
IGRP,60 seconds.
(IGRP Send routing table to all connected routers)
EIGRP,
(After it well converged than If there is a change
in network structure it will send its routing table to all
connected routers)
OSPF, It is same as EIGRP.
(After it well converged than If there is a change
in network structure it will send its routing table to all
connected routers)
The correct RIP timers as per cisco doc
Hellow interval 30 second
dead interval 180
hold down timers 180 second
n flush timers 240 seconds
the eigrp timers
hellow send every 5 second dead 15 second in point to point
in nbma is 60 hellow interval and dead is 180
in ospf
ppp hellow 10 dead 40
brodcast same
but in point to multipoing hellow is 30 secon n dead is 120
second
point multipoint brodcast same
point to multipoint non brodcast
On Cisco catalyst 5000 how would you set the second port on the
controller in the first slot to full duplex?
A.) Set port duplex 1/1 full
B.) Set port duplex 1/2 full
C.) Set port duplex 0/1 full
D.) Set port duplex 0/2 full
What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged
Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom
The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport
Routers can learn about destinations through static routes,
default, or dynamic routing. By default, a router will use
information derived from __________.
A. IGRP
B. RIP
C. IP
D. TCP
During encapsulation, in which order is information packaged?
A. Data, Packet, Segment, Frame
B. Segment, Data, Packet, Frame
C. Data, Segment, Packet, Frame
D. Packet, Data, Segment, Frame
E. Frame, Data, Segment, Packet
F. Bread, Peanut Butter, Jelly, Bread
What parameter is used with statically assigned routers to tell
packets
which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface
Which two commands allow you to verify address configuration
in your unternetword? (Choose two)
A. ping
B. trace
C. verify
D. test ip
E. Echo ip
F. config ip
what is bgp, and what its attributes (thanks to sahin he
sende me notes)
Please try to give answer it will help you in future. after
giving the answer most of them i am selected foro\ 2nd round
of interview
thanks
You create the following standard access-list
access-list 1 deny 1.1.1.1
access-list 1 deny 2.2.2.2
int e0
ip access-group 1 in
Which of the following statements are true, with regard to
traffic flowing
into E0?
A.) This will stop IP packets with a source address of
1.1.1.1 only.
B.) This will stop all IP packets.
C.) This is an invalid configuration.
D.) This will stop no IP packets.
E.) This will stop IP packets with a source address of
2.2.2.2 only.
F.) This will stop IP packets with a source address of
1.1.1.1 and 2.2.2.2.
what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
