| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which two solutions are used to reduce the chance of
distance vector routing loops? (choose two)
A. split horizon
B. route poison
C. area hierarchies
D. link state algorithms | | 1 |
| Identify the order of the 5 step encapsulation?
1) Create the segment
2) Convert the frame to bits
3) Create the packet
4) Create the frame
5) User creates the data
A.) 1,2,4,2,5
B.) 2,1,3,4,5
C.) 5,1,3,4,2
D.) 5,3,4,1,2 | | 1 |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from the Network File server at
1.2.3.4
during the next boot?
A.) boot system flash IOS_filename 1.2.3.4
B.) boot system tftp IOS_filename 1.2.3.4
C.) config-register 0x0 1.2.3.4
D.) boot system rom 1.2.3.4
E.) This can not be done, only the first file in flash can
be used. | | 1 |
| Which range of possible numbers do standard ipx access lists
have?
A. 100 199
B. 600 699
C. 800 899
D. 1000-1099 | | 1 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 4 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| Hi Jitendera, I continuously read your answers which is
more knowlegable than books...
Q.I am facing some problems in subnetting.can you plzz
explain the subnetting process.. will be remain thankful | | 3 |
| Given the IPX address 4a.0002.1111.a999, what is the network ID
and what is the node ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999 | | 1 |
| Which of the following will show an extended access list 150?
A.) sh access-list 150
B.) sh ip int
C.) sh ip access-list
D.) sh access-list 150 extended | | 2 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 1 |
| Hi Gyes, here is new question. can you provide answer of
following question
Like linux, can we windows as router?
If yes how can we able to do this, | | 2 |
| Which two statements are true? (Choose two)
A. Ethernet 802.3 utilizes a half duplex method for data
transfer
B. In a 100 MBS point to point connection a full duplex
connection can provide 400 Mbs of data transfer
C. Ethernet switches can use the full duplex mode to connect
multiple nodes on a single pod of a switch
D. Full duplex Ethernet takes advantage of UTP using one
pair for transmission and the other pair for reception | | 1 |
| Identify 1 characteristic of RARP?
A.) MAC to IP address translation
B.) Connectionless delivery of packets
C.) Can be used to initiate remote O/S load sequence
D.) Generates error and control messages | | 3 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 4 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| What is BGP Synchronization rules?? Can any one explain..??? | Hathway | 2 |
| Which OSI layer provides mechanical, electrical & procedural
specifications for activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
