| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| hi friends i have some problem regarding technical round
ahr round plz tell me what should the right answer
technical questions
1 what is brouter
2 what is the menaing of 10 base2, 10 base 5 and 10baset
3 what is diffrence between bit rate and baud rate.
and this question was tooooooooooo much difficult to me
that
hr said to me that
rank me after the taking the all short of interview | | 5 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 3 |
| Which OSI layer end to end communication, segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| Identify the 2 characteristics regarding MAC addresses?
A.) Contains a network portion and host portion
B.) Always assigned by System Administrator
C.) 48 bits long
D.) Contains a vendor code and serial number | | 1 |
| A big part of the overhead on a network is broadcasts. You
divide a large number of hosts into smaller individual
networks and separate them with the proper device
According to proper networking terminology you have created
separate _______________________,
User Domains
Broadcast Domains
Collision Areas
Broadcast Areas
| | 1 |
| Can anyone explain the STP Security features. Just like BPDU
guard, Root Guard.
Hi JITENDERA, i m specially looking for u????? | | 2 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Which OSI layer defines end to end communication,
segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 1 |
| What is a backoff on an 802.3 networks
A. It is latency in store and forward switching
B. It is the time used for token passing from machine to machine
C. It is the retransmission delay that is enforced when a
collision occurs
D. it is the result of two nodes transmitting at the same
time. The frames from each transmitting device collide and
are damaged. | | 3 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to PAVRAM before becoming enabled | | 1 |
| When a Distance Vector routing protocol detects that a connected
network
has gone down, it sends out a special routing update packet,
telling all
directly connected routers that the distance to the dead
network is
infinity. This is an example of which routing technology?
A.) ICMP.
B.) Only Link State routing protocols have this intelligence.
C.) Triggered updates.
D.) Garrison-4.
E.) Split Horizon.
F.) Poison Reverse. | | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| What is the distance limitation for 100BaseT?
A. 607 ft
B. 25 Meters
C. 1,000 ft
D. 185 Meters | | 1 |
| take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
| AT&T | 6 |
| Tell me CCNA Course + Dump Q/A in chennai? | Wipro | 1 |
| By default, Cisco routers forward GNS SAPs to remote networks.
A. False
B. True | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
