| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Which IP host address range is allowable given an IP address
of 172.37.2.56 and 12 bits of subnetting
A. 172.37.2.48 to 172.37.2.63
B. 172.37.2.48 to 172.37.2.62
C. 172.37.2.49 to 172.37.2.62
D. 172.37.2.49 to 172.37.2.63
E. 172.37.2.55 to 172.37.2.126 | | 1 |
| The Cisco Discovery Protocol (CDP) periodically sends out a
multicast packet (at layer 2). Which command will alter the
default
interval of 60 seconds?
A.) cdp hold 111
B.) cdp wait 111
C.) cdp interval 111
D.) cdp 111
E.) cdp timer 111 | | 1 |
| Which statement is true regarding the user exec and privileged
exec mode?
A.) The '?' only works in Privileged exec
B.) Privileged exec is a subset of the user exec mode
C.) They both require the enable password
D.) User exec is a subset of the privileged exec mode | | 1 |
| When you enter router passwords during the setup dialog what
is the difference between enable and the enable secret
passwords?
A. The enable password is encrypted
B. The enable secret password uses IPSec password authentication
C. The enable secret password cannot be seen as clear text
when viewing the configuration
D. The enable secret password acts as a backup in case the
enable password is compromised | Wipro | 6 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 2 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| Which command should you use to create an IP standard access
list?
A. access-list standard 172.16.4.13
B. access-list 1 deny 172.16.4.13 0.0.0.0
C. access-list 100 deny 172.16.4.13 0.0.0.0
D. access-list 198 deny 172.16.4.13 255.255.255.255 | | 2 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| What was the key reason the International Organization for
Standardization released the OSI model?
A. users could access network servers faster
B. different vendor networks could work with each other
C. the industry could create a standard for how computers work
D. network administrators could increase the overall speed
of their network | | 1 |
| Identify the protocol to test connectivity without
configuring any
layer 3
protocols?
A.) TCP
B.) Ping
C.) IP
D.) CDP
E.) Telnet | | 1 |
| hi friends i have a problem.plz solve this.
i am working some where and i have the number of
swtitch.once my project manger says that we are going to
exapnd our number of employ so plz attech an another
switch.i asked to my jr network engineer that take a witch
and implemnt on that n/w,as he implement the switch on that
n/w.thats network get down,
plz tell me what is the reason of that.
| | 1 |
| what is the difference between
1 router and switch
2 router and hub
3 hub and switch
4 bridge and switch
| Hathway | 1 |
| When determining whether or not to route a LAN segment,
which rule of
thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| Identify the command mode necessary to enter the standard ping
command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)# | | 1 |
| Which two physical interfaces support PPP? (Choose two)
A. Ethernet
B. Token Ring
C. Synchronous serial
D. Asynchronous serial | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
