| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command that saves the configuration stored in
RAM to
NVRAM?
A.) copy running-config startup-config
B.) copy tftp running-config
C.) copy startup running
D.) copy active to backup | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| what is burst rate | ASD-Lab | 1 |
| LAN stands for which of the following?
A.) Local Area Network
B.) Local Arena Network
C.) Local Area News
D.) Logical Area Network | | 4 |
| Which can be logged by IPX extended access lists?
A.) source address
B.) protocol
C.) source socket
D.) access list number
E.) destination socket
F.) destination address | | 1 |
| Which of the following is a valid extended IP access-list?
A.) router(config)# access-list 101 permit tcp host
172.16.30.0 any eq
21 log
B.) router# access-list 101 permit tcp host 172.16.30.0 any
eq 21 log
C.) router(config)# access-list 101 permit any any 172.16.30.0
D.) router(config)# access-list 101 permit ip host
172.16.30.0 any eq 21
log | | 2 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| Which command will give the following output:
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 0 0 0/0 -
1 AUX 9600/9600 - - - - - 0 0 0/0 -
* 2 VTY - - - - - 2 0 0/0 -
3 VTY - - - - - 0 0 0/0 -
4 VTY - - - - - 0 0 0/0 -
5 VTY - - - - - 0 0 0/0 -
6 VTY - - - - - 0 0 0/0 - | | 1 |
| hi shain
i have got some virus who make the .exe file that is
duplicate of original file on my server 2007 windows can u
suggest me any anti virus
help help please help | | 4 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE
cables. To which router would you add the clockrate command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | | 1 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| Which three of the following are true statements about
connection-oriented sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged the are retransmitted by
the receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 1 |
| Identify the OSI layer associated with bits?
A.) Physical
B.) Network
C.) Binary
D.) Data link | | 1 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
