| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Why Clock rate command is not configured on ethernet
interface of a router? | | 3 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode | Wipro | 10 |
| Which of the following are Presentation Layer standards?
A.) JPEG and PICT
B.) MPEG and MIDI
C.) ASCII and EBCDIC
D.) NFS and SQL | | 2 |
| If a frame is received at a switch and only the destination
hardware address is read before the frame is forwarded, what
type of
switching method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a
Frame Relay network, which encapsulation type would you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Which of the following is a layer 2 device?
A.) Switch
B.) Bridge
C.) Repeater
D.) Hub | | 1 |
| Which IP Address Class is INCORRECTLY paired with its range
of network numbers?
A. Class A addresses include 192.0.0.0 through 223.255.255.0
B. Class A addresses include 1.0.0.0 through 126.0.0.0
C. Class B addresses include 128.0.0.0 through 191.255.0.0
D. Class C addresses include 192.0.0.0 through 223.255.255.0
E. Class D addresses include 224.0.0.0 through 239.255.255.0 | | 1 |
| What is the regional Telco office called, where the customers
local loop
terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 1 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 2 |
| MIDI and MPEG are examples of what layer of the OSI seven layer
model?
A.) Session
B.) Network
C.) Datalink
D.) Transport
E.) Application
F.) Presentation | | 1 |
| If i connect two routers through ethernet cable and serial
cable then which has high speed and which is better among
two? | Compaq | 9 |
| Which two commands allow you to verify address configuration
in your unternetword? (Choose two)
A. ping
B. trace
C. verify
D. test ip
E. Echo ip
F. config ip | | 2 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| Which of the following is a layer 2 device?
A.) Switch
B.) Router
C.) Repeater
D.) Hub | | 3 |
| What command can you type to view the connections after
telneting
into multiple routers simultaneously?
A.) sh users
B.) sh ports
C.) sh host
D.) sh sessions | | 1 |
| As a system administrator, you need to provide your routers
with a Domain Name System (DNS) server. How many DNS
servers can you specify with one command?
A. 6
B. 1
C. 2
D. 4 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
