| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| What would be the first command from global configuration
mode to
enable
RIP on your router for interface E0, with an address of
181.86.4.4 and
mask of 255.255.255.0 ?
A.) router rip
B.) network 181.89.4.0 255.255.255.0
C.) router rip int e0
D.) router rip 181.86.0.0
E.) router rip 181.86.4.0
F.) network 181.86.0.0 | | 1 |
| What is the purpose and default value of the CDP timer command?
A.) 90 seconds; interval before an entry expires
B.) 60 seconds; interval between updates
C.) 60 seconds; interval before an entry expires
D.) 90 seconds; interval between updates | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 1 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| An autonomous system can only exist if all routers in that
system meet which criteria?
A. interconnected
B. run the same routing protocol
C. assigned same autonomous system number
D. run IGRP only
E. run RIP only | | 1 |
| Which layer of the 7 layer model provides services to the
Application layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| What does a router do with a packet that it does not have a
destination
network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 1 |
| How many access lists are allowed per interface?
A. One per port, per protocol
B. Two per port, per protocol
C. Unlimited
D. Router interface +1 per port. | | 1 |
| LMI operates between the Frame Switch and what other device?
A.) CPE device
B.) Another Frame Switch
C.) X.25 switch
D.) Novell File Server | | 1 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
