| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| In Novell's use of RIP, there are two metrics used to make
routing decisions. Select the two metrics.
A. Ticks.
B. Hops
C. Loops
D. Counts | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Which of the following are examples of ICMP?
A.) Traceroute
B.) Web Browsing
C.) Ping
D.) Telnet
E.) Destination Unreachable message from a router
F.) Inverse Tunnels | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 1 |
| why we give clock rate to DCE and not to DTE
what is the difference in the two. | | 1 |
| Which statement should you use to deny FTP access (only)
from network 210 93 105 0 to network 223 8 151 0?
A. access list 1 deny 210 93 105 0 0 0 0 0 any eq ftp access
list 1 permit any
B. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151
0 0 0 0 255 eq ftp
C. access list 100 deny ip 223 8 151 0 0 0 0 255 any eq ftp
access list 100 permit hp any any
D. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151
0 0 0 0 255 eq ftp access list 100 permit ip any any | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| Although Cisco IOS 11.2 and later can auto-detect the LMI
type in
Frame Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a
B.) encapsulation frame-relay q933a
C.) don't need to, it is the default
D.) encapsulation q933a
E.) encapsulation frame-relay type=q933a | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 3 |
| Which three commands are used to configure information into
RAM on a router? (Choose three)
A. configure memory
B. configure terminal
C. configure overwrite
D. copy tftp startup-config
E. copy running-config startup-config
F. copy startup-config running-config | HCL | 5 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to PAVRAM before becoming enabled | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| I want to configure a serial interface on a 7500 with a VIP
card.
What global config command would give me access to a serial
interface on
a 7500?
A.) int 1/0/0
B.) int s 1/0/0
C.) int s 1/1
D.) int s0.1
E.) int s1 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
