| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which of the following is an example of the Physical Layer?
A.) SQL
B.) IP
C.) LLC
D.) DDP
E.) Ethernet | | 2 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| IGRP supports a feature that allows traffic to be
distributed among up to 6 (4 default) paths to provide
greater overall throughput and reliability. What is this
called?
A. unequal-cost load balancing
B. equal-cost load balancing
C. proportionate load balancing
D. low cost load balancing | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home
D. a standard 28.8 analog dialup connection to the user at home | | 2 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | | 1 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is
the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 2 |
| what is nat.types of nat | | 3 |
| Which type of Ethernet framing is used for TCP/IP and
AppleTalk?
A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP | Wipro | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 2 |
| what is farme realy.and on which layer it work | | 1 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| How ICMP is used in ping and traceroute facilities | | 3 |
| What do the following commands accomplish?
access-list 1 permit 172.16.0.0 0.0.255.255
interface ethernet 0
IP access-group 1 out
interface ethernet 1
IP access-group 1 out
A. Only traffic from the source network 172.16.0.0 will be
blocked.
B. Only traffic from the source network 172.16.0.0 will be
forwarded.
Non-172.16.0.0 network traffic is blocked.
C. Non-172.16.0.0 traffic will be forwarded.
D. All traffic will be forwarded. | | 1 |
| Name a major component of the Point-to-Point Protocol (PPP) to
negotiate and set up control options on the WAN data link.
A.) RFC 1661
B.) High Level Datalink Protocol (HDLC)
C.) Challenge Handshake Authentication Protocol (CHAP)
D.) SS7
E.) Link Control Protocol (LCP) | | 2 |
| thnx jitender...its me shridh...m working for SG ltd..the
situation iz like ths -at a specific time in our company the
internet connectivity goes off...v hav two networks in our
company...but out of it only one link goes down for 5-10
sec...a fastethernet port becomes down for few sec and
automatically becomes Up... Is this occures becoz of Power??
If yes thn y the 2nd network is not affected??
plz tel me jitender how to resolve ths problem?
as u sd loop in switch is the primary cause of ths....i
wanna know how to resolve it...thnx for ur replys jitender
sinha. | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
