| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| Which of the following is a characteristic of a switch, but
not of
a repeater?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 2 |
| What is the protocol number for UDP?
A.) 6
B.) 17
C.) 25
D.) 21 | | 2 |
| What is link aggregration?? How many types of protocol are
used on that??? | Hathway | 3 |
| hi shain/sudeep and rest of all plz answer these question
for help some one as soon as possible
what is stub area
what is transit area
let there are three area in ospf a0 a2 and a3 if a2 and a3
is coneted
through each other will they comnicate | | 3 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| What is a function of a reliable transport layer connection?
A. route selection
B. acknowledgements
C. session checkpoints
D. system authentication | | 2 |
| How do you get help on a command after you have received the
% incomplete command response from a switch CLI?
A. type "history" to review the prompt before the error
B. enter a question mark to display all the console commands
C. type help followed by the command to see command parameters
D. reenter the command followed by a question mark to view
keywords | | 1 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| How we ping ICMP a NIC with a correct IP address but with
wrong MAC address
Do all NIC's can run inpromiscuous mode | Cisco | 3 |
| What is the most common layer 2 device?
A. Hub
B. Bridge
C. Switch
D. Router | | 1 |
| Which of the following is a layer 2 device?
A.) Switch
B.) Bridge
C.) Repeater
D.) Hub | | 2 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| The CSMA/CD Ethernet IEEE committee is defines as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| What command do you use to disable domain lookup?
A.) no domain-lookup
B.) domain no-lookup
C.) lookup no-domain
D.) no ip domain-lookup | | 1 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to do
it | | 1 |
| What does the "IPX maximum-paths 2" command accomplish?
A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths. | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
