| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| You want to clear the outputs on your serial interface
showing errors on the interface. Which command do you type? | | 1 |
| Given the global configuration commands:
'banner motd #'
'Hello #'
When would the message be displayed?
A.) The message of the day banner shows up before login.
B.) The message of the day banner shows up during logoff.
C.) These commands are not the right syntax for MOTD.
D.) Message of the day banners are displayed upon entering
global config
mode.
E.) Message of the day banners are not possible.
F.) The message of the day would be, 'Hello #' | | 1 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| What do the following statements in an extended access list
accomplish?
access-list 101 deny TCP 172.16.4.0 0.0.0.255 172.16.3.0
0.0.0.255 eq 21
access-list 101 deny TCP 172.16.4.0 0.0.0.255 172.16.3.0
0.0.0.255 eq 20
access-list 101 permit TCP 172.16.4.0 0.0.0.255 0.0.0.0
255.255.255.255
A. This will block ftp traffic.
B. This will block http traffic.
C. This will permit ftp traffic.
D. This will permit tftp traffic. | | 1 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| What is the standard ISDN term for a native ISDN modem?
A.) ET
B.) LE
C.) TE2
D.) TE3
E.) TA | | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| What are two functions of the ICMP protocol? (Choose two)
A. to map IP addresses to Ethernet addresses
B. to map common names to network addresses
C. to forward SNMP alerts to management consoles
D. to generate an echo reply in response to a ping test
E. to send a host or pod unreachable message from a router
to the source of an undeliverable packet | | 1 |
| If you are in IOS user mode, which command do you use to
enter the privileged mode?
A. Set
B. Enable
C. Configure
D. Privileges | | 1 |
| Identify the type of hardware required to connect a Token ring
network to
an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| What is the default LMI type?
A.) Cisco
B.) ANSI
C.) IETF
D.) Q933a | | 2 |
| Windowing is a type of?
A.) Negative acknowledgement
B.) Address resolution
C.) Layer transition mechanism
D.) Flow control | | 1 |
| Which two protocol tools use ICMP? (Choose two)
A. ping
B. telnet
C. configure
D. traceroute
E. show commands
F. standard access lists | | 3 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| there is three mode of vtp let there are three switch s1 in
server mode s2 in transparent mede and s3 in clint mode
then will that tranparnt mode going to effect the network if
yes then how and if no then what it will do | IBM | 1 |
| Which IP Address Class is INCORRECTLY paired with its range
of network numbers?
A. Class A addresses include 192.0.0.0 through 223.255.255.0
B. Class A addresses include 1.0.0.0 through 126.0.0.0
C. Class B addresses include 128.0.0.0 through 191.255.0.0
D. Class C addresses include 192.0.0.0 through 223.255.255.0
E. Class D addresses include 224.0.0.0 through 239.255.255.0 | | 3 |
| What is the administrative distance for RIP?
A.) 100
B.) 90
C.) 120
D.) 110 | | 4 |
| The following is partial output from a routing table,
identify the
2 numbers in the square brackets; '192.168.10.0 [100/1300]
via 10.1.0.1,
00:00:23, Ethernet1'
A.) 100 = metric, 1300 = administrative distance
B.) 100 = administrative distance, 1300 = hop count
C.) 100 = administrative distance, 1300 = metric
D.) 100 = hop count, 1300 = metric | | 1 |
| Which of the following is True regarding passwords on a
Cisco router?
A. All passwords can be encrypted
B. All passwords can be entered using the set-up dialogue
C. A password can be set before a user can enter the
privileged mode
D. A password can be set for individual lines
E. TACACS or Radius password authentication can be used. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
